Canon LV-7390 Manuel D'Instructions

6

Immediately turn the power off, unplug the projector, 

and contact your dealer under the following 

conditions, otherwise a fire or an electric shock may 

result. 

–  If smoke comes out from it.

–  If it emits a strange odor, or makes a strange noise.

–  If lamp goes out with a loud bang.

–  If water or any other liquid gets into it.

–  If metal or foreign objects get inside it.

–  If it is knocked down or dropped and the cabinet is 

broken.

Follow the instructions below when using the power 

cable, otherwise a fire, an electric shock, or injury 

may result. 

–  Do not place heavy objects on the power cord or 

position the power cord under the projector. Doing 

so may damage the power cord.

–  Do not run the power cord under a carpet. As it 

goes unnoticed, excessive load may be applied on 

the cord unintentionally. 

–  Do not modify, bend forcibly, twist, or pull the power 

cord. 

–  Do not place the power cord near heat generating 

equipment or heat it.

–  Do not bend, wind, or bind excessively the power 

cord when using it.

–  Be sure to connect the projector to a grounded 

outlet. Failure to do so may result in an electric 

shock.

–  Do not continue to use a damaged power cord. If 

the power cord is damaged, take it to your dealer 

and have it replace. 

–  Use only the supplied power cord.

Follow the instructions below when handling the 

power plug or connector, otherwise a fire, an electric 

shock, or injury may result.

–  Use the projector within the voltage range specified 

on the projector (AC 100 V– 40 V). 

–  Insert the power plug or connector into the power 

outlet firmly. Do not use a damaged or loosen 

power plug or connector.

–  Be sure to hold the power cord plug or connector 

when disconnecting it from the power outlet. If the 

power cord itself is pulled, it may be damaged. 

–  Do not plug or unplug the power cord with wet 

hands.

–  Disconnect the power cord from the power outlet 

before cleaning the projector.

–  Do not stick metal objects into the electrical 

contacts of the power plug or connector.

Follow the instructions below to install or handle the 

projector. Otherwise, a fire, an electric shock, or injury 

may result. 

–  Do not touch the projector, power cord, or cables 

when lighting begins.

–  Do not use the projector in a bathroom or shower 

room.

–  Do not expose the projector to rain, snow, or use 

near water.

–  Do not insert metal objects into the projector 

through the air vents.

–  Do not place the containers with water on the 

projector.

–  Do not install in the locations exposed to oily vapors 

or smoke (e.g., near a cooking table or humidifier).

–  Before moving the projector, turn the power off and 

disconnect the power cord and all cables.

–  Do not put spray cans in front of the exhaust 

vent. When spray cans are exposed to heat, the 

pressure in them will increase and explode.

–  Do not open nor remove the cabinet. There are 

high voltage components inside the projector. 

Contact your dealer for inspection, adjustment, and 

service. 

–  Do not attempt to disassemble the projector 

(including expendable parts) or remote control unit.

–  Do not look into the lens while the projector is used. 

Strong light may hurt your eyes. Be especially 

careful that small children do not look into the lens.

–  When an extension cord is necessary, be sure that 

the total current load of all equipment connected to 

the extension cord does not exceed the specified 

rating of the extension cord.

–  Periodically unplug the power cord and remove the 

dust that builds up on the power cord or connector.

Follow the instructions below when handling the 

batteries. Failure to do so may cause explosion, heat 

generation, a fire, or leakage of the battery fluid. 

–  Do not heat or disassemble the batteries, or throw 

them into fire.

–  Do not attempt to recharge the batteries.

Follow the instructions below when the lamp is 

replaced or breaks.

–  Always unplug the power cord before replacing the 

lamp.

–  When the lamp breaks, shards of glass may 

scatter in the lamp housing. Contact your dealer for 

cleaning or inspecting the projector, or replacing 

the lamp.