Canon WX6000 Manuel D’Utilisation
202
Troubleshooting
LED Indicator Meanings
When there is a problem with the projector, the LED indicator on the side of the projector
illuminates or flashes continuously after the projector is turned off.
illuminates or flashes continuously after the projector is turned off.
• Wait until the cooling fan stops and disconnect the power plug from the electrical outlet
before dealing with the problem.
LED indicator
status
Meaning
Countermeasure
WARNING and
TEMP are lit.
TEMP are lit.
Temperature
abnormality
abnormality
The temperature inside the projector is too high for some
reason or the outside air temperature is higher than the oper-
ating range. If the problem is inside the projector, check
whether the projector is installed and operating normally,
unplug the projector from the power outlet to cool down the
projector interior and then restart projection. If the air intake
or exhaust vent is blocked, remove the obstacle. If the same
warning occurs again, there may be a malfunction in the
projector. Contact the Canon Customer Support Center.
reason or the outside air temperature is higher than the oper-
ating range. If the problem is inside the projector, check
whether the projector is installed and operating normally,
unplug the projector from the power outlet to cool down the
projector interior and then restart projection. If the air intake
or exhaust vent is blocked, remove the obstacle. If the same
warning occurs again, there may be a malfunction in the
projector. Contact the Canon Customer Support Center.
WARNING and
LAMP are lit.
LAMP are lit.
Faulty lamp
The lamp does not illuminate. Turn the power off and then
back on and check whether or not the lamp illuminates.
Also, check whether the air intake or exhaust vent is
blocked, and whether the air filter is clogged with dust. The
warning may indicate if the air flow in and out of the projector
is blocked, or if the internal temperature of the projector
rises. If the air filter is clogged, clean or replace the air filter.
(
back on and check whether or not the lamp illuminates.
Also, check whether the air intake or exhaust vent is
blocked, and whether the air filter is clogged with dust. The
warning may indicate if the air flow in and out of the projector
is blocked, or if the internal temperature of the projector
rises. If the air filter is clogged, clean or replace the air filter.
(
) If the lamp does not illuminate, replace it. If the
same warning occurs again, there may be a malfunction in
the lamp drive circuit. Contact the Canon Customer Support
Center.
the lamp drive circuit. Contact the Canon Customer Support
Center.
WARNING
flashes 3
times, LAMP is
lit.
flashes 3
times, LAMP is
lit.
Faulty lamp
cover
cover
The lamp cover is open. Unplug the projector from the elec-
trical outlet, then install the lamp cover correctly and turn on
the projector again. If the lamp cover has been installed
properly, there may be a malfunction in the lamp cover
detection switch. Contact the Canon Customer Support
Center.
trical outlet, then install the lamp cover correctly and turn on
the projector again. If the lamp cover has been installed
properly, there may be a malfunction in the lamp cover
detection switch. Contact the Canon Customer Support
Center.
WARNING
(only) flashes 4
times repeat-
edly.
(only) flashes 4
times repeat-
edly.
Faulty cool-
ing fan
ing fan
There may be a malfunction in the cooling fan or another
component. Unplug the projector from the electrical outlet,
then plug it into the outlet and turn on the projector again.
Contact the Canon Customer Support Center if the same
warning occurs again.
component. Unplug the projector from the electrical outlet,
then plug it into the outlet and turn on the projector again.
Contact the Canon Customer Support Center if the same
warning occurs again.
WARNING
(only) flashes 5
times repeat-
edly.
(only) flashes 5
times repeat-
edly.
Faulty power
supply
supply
Abnormal voltage is applied to some parts in the power sup-
ply or another failure may have occurred. Unplug the projec-
tor from the electrical outlet, then plug it back into the outlet
and turn on the projector again. Contact the Canon Cus-
tomer Support Center if the same warning occurs again.
ply or another failure may have occurred. Unplug the projec-
tor from the electrical outlet, then plug it back into the outlet
and turn on the projector again. Contact the Canon Cus-
tomer Support Center if the same warning occurs again.