Toshiba B-SX8T Manuel D’Utilisation
2. SYSTEM MODE
EO13-33002
2.2 Parameter Setting
2-18
2.2 Parameter Setting
Outline of Parameter Setting
In the Parameter Setting mode, various kinds of parameters, such as communication, key, LCD, etc. can be set.
This will allow a use of the printer to comply with your operating conditions.
The Parameter Setting menu contains the following:
This will allow a use of the printer to comply with your operating conditions.
The Parameter Setting menu contains the following:
NOTE: Baud rate, Data length, Parity, and Transmission control code should be set to the same values as those of the host
computer. Failure to do this causes improper operation.
Character code selection
Character zero selection
Baud rate selection
Data length selection
Stop bit length selection
Parity selection
Flow control code selection
LCD language selection
Auto forward wait selection
[PAUSE]
<2>PARAMETER SET
FONT CODE PC-850
FONT CODE PC-850
<2>PARAMETER SET
ZERO FONT 0
ZERO FONT 0
<2>PARAMETER SET
SPEED 9600bps
SPEED 9600bps
<2>PARAMETER SET
DATA LENG. 8bits
DATA LENG. 8bits
<2>PARAMETER SET
STOP BIT 1bit
STOP BIT 1bit
<2>PARAMETER SET
PARITY EVEN
PARITY EVEN
<2>PARAMETER SET
XON+READY AUTO
XON+READY AUTO
<2>PARAMETER SET
LCD ENGLISH
LCD ENGLISH
<2>PARAMETER SET
FORWARD WAIT OFF
FORWARD WAIT OFF
<2>PARAMETER SET
[PAUSE]
[PAUSE]
[PAUSE]
[PAUSE]
[PAUSE]
[PAUSE]
[PAUSE]
[PAUSE]
[PAUSE]
<2>PARAMETER SET
EURO CODE B0
EURO CODE B0
<2>PARAMETER SET
AUTO HD CHK OFF
AUTO HD CHK OFF
<2>PARAMETER SET
ACK/BUSY TYPE1
ACK/BUSY TYPE1
<2>PARAMETER SET
WEB PRINTER OFF
WEB PRINTER OFF
<2>PARAMETER SET
SENS POSI CENTER
SENS POSI CENTER
<2>PARAMETER SET
EX.I/O TYPE1
EX.I/O TYPE1
<2>PARAMETER SET
PLUG & PLAY OFF
PLUG & PLAY OFF
<2>PARAMETER SET
LBL/RBN END TYPE1
LBL/RBN END TYPE1
<2>PARAMETER SET
PRE PEEL OFF OFF
PRE PEEL OFF OFF
<2>PARAMETER SET
BACK SPEED STD
BACK SPEED STD
Euro code selection
Auto print head check selection
Centronics ACK/BUSY timing
selection
selection
Web printer function selection
Media sensor selection
Expansion I/O interface type
selection
selection
Plug & Play selection
Label end/Ribbon end selection
Pre-strip selection
Reverse feed speed selection
[PAUSE]
[PAUSE]
[PAUSE]
[PAUSE]
[PAUSE]
[PAUSE]
[PAUSE]
[PAUSE]
[PAUSE]
[PAUSE]
<2>PARAMETER SET
MAXI CODE TYPE1
MAXI CODE TYPE1
Maxi code specification selection
Control code selection
<2>PARAMETER SET
CODE ESC,LF,NUL
CODE ESC,LF,NUL
[PAUSE]
[PAUSE]
Strip wait status selection
<2>PARAMETER SET
PEEL OFF STS OFF
PEEL OFF STS OFF
[PAUSE]
<2>PARAMETER SET
FEED KEY FEED
FEED KEY FEED
Feed key function selection
[PAUSE]
[PAUSE]
<2>PARAMETER SET
PEEL OFF TRQ R0
PEEL OFF TRQ R0
Strip motor torque selection
<2>PARAMETER SET
KANJI CODE TYPE1
KANJI CODE TYPE1
Kanji code selection
[PAUSE]
Head up cut selection
Ribbon save function selection
<2>PARAMETER SET
HEAD UP CUT OFF
HEAD UP CUT OFF
<2>PARAMETER SET
RBN SAVE ON (TAG)
RBN SAVE ON (TAG)
[PAUSE]
[PAUSE]
[PAUSE]
Ribbon type selection
<2>PARAMETER SET
RIBBON NON TRANS
RIBBON NON TRANS
<2>PARAMETER SET
INPUT PRIME OFF
INPUT PRIME OFF
Input prime selection
[PAUSE]
[PAUSE]
<2>PARAMETER SET
STABILIZER ON
STABILIZER ON
Stabilizer function selection