SATO CL412e Manuel D’Utilisation

Index-2

Idle Roller  9-14
IEEE 1284 Parallel Interface  3-4, 8-2
Ignore CR/LF  2-16
Installation Considerations 1-9
Installation Problems, Lan Ethernet Interface  8-5
Interface Options  10-21
Interface Slot  1-3
Interface Specifications  3-1
Interface Types  3-1

Label Cutter Kit Installation  9-2
Label Dispenser Kit  9-6
Label Dispenser Installation  9-6
Label Dispenser Latch  9-14
Label Gap Adjustment  4-10
Label Guide  1-5
Label Sensor Assembly  6-25
Label Sensor Module  6-26
Label Sensor Selection  2-5
Label Sensor  1-6, 6-24
Label Taken LED  1-7,1-8
Labels  9-14
Lan Ethernet Interface  8-5
LCD  Panel, Advanced Mode  2-13
LCD  Printer, Card  Mode  2-17
LCD Display Panel  1-7, 1-8
LCD Panel, Normal Mode  2-9
LCD Panel  Configuration  2-8
LCD Panel, Clear Non-Standard Protocol  2-37
LCD Panel, Counters  Mode  2-32
LCD Panel, Maintenance Mode, Factory Mode  2-35
LCD Panel, Service  Mode  2-25
LCD Panel, Firmware Download Mode  2-39
Line Key   1-7, 1-8

M8400 Emulation Mode  2-4
Main Circuit Board  6-2
Main PCB Assembly  10-20
MAIN PCB BOARD  9-21
Mechanical Adjustments  5-1
Media Holder  1-5
Mem Select  2-17
Memory Format  2-24
MEMORY MODULE PCB  6-5
MEMORY PCB BOARD  9-16
Mode Selection  2-4
Multi Job Buffer  3-3

NetWare Troubleshooting  8-7

Offset Label Stop Position Adjustment  4-12

Operation Panel  1-7
Optional Accessories 1-9, 9-1

Paper Check Window  1-2
Parity Selection  2-2
PCMCIA Memory Expansion Installation  9-16
PCMCIA Memory  Expansion Slot  1-3
PCMCIA Memory Option  10-22
Peel Bar   9-11, 9-13
Physical Characteristics  1-  2
PIN Assignments - IEEE 1284  Cable End  3-5
PIN Assignments -  RS232C Printer End  3-6
Pin Assignments  3-11
Pitch Offset Adjustment  2-10
Platen  6-18
Potentiometer Assignments & Adjustments  4-6
Potentiometers  1-7, 1-8
Power Supply  6-9, 6-10
Power Switch  1-3
Print Buffer Hex Dump   8-17
Print Darkness Adjustment  4-16
Print Darkness Setting  2-9
Print Head Alignment Adjustment  5-9
Print Head Assembly  1-4, 10-5
Print Head Balance Adjustment  5-8
Print Head Position Alignment  5-7
Print Head  6-14
Print Mode Selection  2-3
Print Offset  2-14
Print Position Adjustment  4-8
Print Quality Problems  8-11
Print Speed Adjustment  2-10
Printer Features  1-3
Printer Set up  2-3
Priority Setting LCD Command  2-31
Protocol Code Selection  2-4
Protocol Selection  2- 2
Ready/Busy Flow Control  3-8
Real Time Clock Installation  9-26
Receive Buffer Hex Dump  8-17
Receive Buffer Selection  2-3
Receive Buffer  3-3
Removing the Main PCB Board  9-17
Repeat Print via External Signal  2-6
Repeat Print  3-13
Replacement Procedures  6-1
Replacing the Display Panel PCB  6-28
Replacing the Fuses  6-7
Replacing the Head Open Switch  6-27
Replacing the Label Sensor Module  6-26
Replacing the Label Sensor  6-24
Replacing the Main Circuit Board  6-2
Replacing the Platen  6-17
Replacing the Power Supply  6-9
Replacing the Print Head  6-14
Replacing the Ribbon Drive Clutch Washers  6-19