OKI C810 Manuel D’Utilisation
Menu functions - C830 > 52
C
ALIBRATION
Change
Password
Password
New
Password
Password
xxxxxxxxxxxxxx
Sets a new password to enter Admin Setup menu
From 6 to 12 alpha/numeric digits can be entered.
From 6 to 12 alpha/numeric digits can be entered.
Verify
password
password
xxxxxxxxxxxxxx
Forces the User to input the new password to enter Admin
Setup.
From 6 to 12 alpha/numeric digits can be entered.
Setup.
From 6 to 12 alpha/numeric digits can be entered.
Settings
Reset
Settings
Settings
Execute
Resets EEPROM of CU. Resets User menu to the factory
default.
If Execute is selected, exits from the menu.
default.
If Execute is selected, exits from the menu.
Save
Settings
Settings
Execute
Saves menus currently set. With this function, the menus
with which operation was last performed are saved, and
overwrites with them menus that were previously saved.
When the Enter button is pressed, the following
confirmation message appears.
Are You Sure? Yes/No
When No is selected, the preceding menus are restored.
When Yes is selected, the current menu settings are
saved and this menu is exited.
with which operation was last performed are saved, and
overwrites with them menus that were previously saved.
When the Enter button is pressed, the following
confirmation message appears.
Are You Sure? Yes/No
When No is selected, the preceding menus are restored.
When Yes is selected, the current menu settings are
saved and this menu is exited.
ITEM
SETTINGS
EXPLANATION
Auto Density
Mode
Mode
On/Off
Enables/disables automatic density adjustment.
Adjust Density
Execute
If Execute is selected, the printer will immediately
adjust density and reflect it in TRC compensation.
This adjustment must be executed when the
printer is idling. It can become invalid if executed
in any other state.
adjust density and reflect it in TRC compensation.
This adjustment must be executed when the
printer is idling. It can become invalid if executed
in any other state.
Adjust
Registration
Registration
Execute
When this menu is selected, the printer performs
AutoAdjust Registration.
This adjustment must be executed when the
printer is idling.
AutoAdjust Registration.
This adjustment must be executed when the
printer is idling.
Print Tuning
Pattern
Pattern
Execute
Prints the pattern for the user to adjust TRC.
Ordinarily, this function is not needed because TRC is
automatically adjusted to the recommended levels
through density adjustment and TRC compensation.
Adjustment results will be reflected as offset values
(addition) to the corrections through the Adjust
Density/TRC Compensation function.
Ordinarily, this function is not needed because TRC is
automatically adjusted to the recommended levels
through density adjustment and TRC compensation.
Adjustment results will be reflected as offset values
(addition) to the corrections through the Adjust
Density/TRC Compensation function.
Cyan/Magenta/
Yellow/Black
Tuning
Yellow/Black
Tuning
Highlight
-3,-2,-1,
0,+1,+2,+3,
0,+1,+2,+3,
Adjusts HIGHLIGHT (light area) of the TRC.
+ = Darker
- = Lighter
+ = Darker
- = Lighter
Mid-Tone
-3,-2,-1,
0,+1,+2,+3,
0,+1,+2,+3,
Adjusts MID-TONE area of the TRC.
+ = Darker
- = Lighter
+ = Darker
- = Lighter
Dark
-3,-2,-1,
0,+1,+2,+3,
0,+1,+2,+3,
Adjusts DARK area of the TRC.
+ = Darker
- = Lighter
+ = Darker
- = Lighter
Cyan/Magenta/
Yellow/Black
Darkness
Yellow/Black
Darkness
-3,-2,-1,
0,+1,+2,+3,
0,+1,+2,+3,
Adjusts the engine density.
The Darkness settings for each of CMYK will be
reflected as offset values (addition) to the corrections
through the Adjust Density/TRC Compensation
function.
The Darkness settings for each of CMYK will be
reflected as offset values (addition) to the corrections
through the Adjust Density/TRC Compensation
function.
ITEM
SETTINGS
EXPLANATION