Mitsubishi Electronics XD200U Manuel D’Utilisation

EN – 24

The following offers solutions to some of the common problems you may encounter. We suggest that you consult
this chart before contacting your dealer.

• The air inlet grille, outlet grille  or air filter is

clogged with dust or some other obstruction.

POWER indicator does not light up.
• Power cord is unplugged from the outlet.
• Power cord is disconnected from the projector.
• The main switch is turned off.
• The lamp lid is open.
Power indicator blinks red.
• The projector has been turned on again too soon

after having been turned off.

• When the power switch was turned off while

the fan was running, during or after lamp
operation.

• The room temperature is too high.

(Does the STATUS indicator show an unusual
condition?)

• Lamp is no longer working.

• The lamp cover is not closed.
• When the STATUS indicator is on or blinking,

the main unit requires repairs.

• Lens is covered by lens cap.
• When the STATUS indicator is on or blinking,

the main unit requires repairs.

• The equipment connected to this projector is not

turned on.

• Other equipment is not connected properly.
• The input source is not selected correctly.

• The air inlet grille, outlet grille  or air filter is

clogged with dust or obstructed.
(In this case, the STATUS indicator does not light up.)

• The projector is not at a right angle to the screen.

• Brightness, tint and color are not adjusted correctly.

• The projecting distance is beyond the focused area.
• Lens is dirty.

• Screen size exceeds screen size specifications.

• Brightness and contrast are not adjusted correctly.
• FINE adjustment is not made correctly.
• Tracking is not adjusted.
• The projector is not at a right angle to the screen.

• Remove the obstruction.

• Plug the power cord into the outlet.
• Insert the power cord into the projector.
• Turn the main switch on.
• Close the lamp lid.

• Wait for the lighting sequence.

• Turn the power switch on and off several times.

• Refer to "Indicators" on page 23.

• Replace the lamp with a new one.

• Close the cover correctly.
• Contact your dealer.

• Take the lens cap off.
• Replace the lamp with a new one.

• Turn on the connected equipment.

• Confirm the connections.
• Select the correct source according to the equip-

ment connected to this projector.

• Remove the obstruction and turn off the main

power switch. After about 10 minutes, turn the
projector on.

• Adjust the angle of the projector to make a right

angle to the screen. See page 12.

• Adjust brightness, tint and color correctly.

• Adjust the projecting distance. See page 9.
• Clean lens.
•

Use a screen size to within 40" to 300".

• Adjust brightness, contrast.
• Make FINE adjustment.
• Adjust tracking.
• Adjust the angle of the projector to make a

right angle to the screen. See page 12.

• The cable for connection with other equipment

is not plugged securely into the terminal.

• The projector is installed too close to other

equipment.

• Volume is not turned up.
• Connection to other equipment is not made correctly.

• The PC monitor is not turned on.

• This is typical of the projector.

• The operation is incorrectly made due to noise or

interference.

• Plug the connecting cable securely into the

terminal. See pages 10-11.

• Increasethe distance between the projector

and other equipment.

• Turn up the volume.
• Check connections.  See pages 10-11.

• Turn on the monitor.

•

Turn off the main power, wait about 10 min-
utes, and turn on the main power again

.

The power is off.

No picture appears
on the screen.

The image is
turned off.

The image is
distorted.

The image is dark.

The image is
blurred.

The image is dis-
torted on the screen
and noise is heard.

No sound is heard.

Adjustments cannot be
made.

Warm air comes out of
the exhaust vents.

Nothing is displayed on
the PC monitor.

• This mark is displayed when an invalid operation is executed. This is not failure.

 is displayed.