Cisco Systems 3130 Manuel D’Utilisation
36-56
Cisco Catalyst Blade Switch 3130 for Dell Software Configuration Guide
OL-13270-01
Chapter 36 Configuring QoS
Configuring Standard QoS
Step 17
trust [cos | dscp | ip-precedence]
Configure the trust state, which QoS uses to generate a CoS-based or
DSCP-based QoS label.
DSCP-based QoS label.
Note
This command is mutually exclusive with the set command
within the same policy map. If you enter the trust command,
omit Step 18.
within the same policy map. If you enter the trust command,
omit Step 18.
By default, the port is not trusted. If no keyword is specified when the
command is entered, the default is dscp.
command is entered, the default is dscp.
The keywords have these meanings:
•
cos—QoS derives the DSCP value by using the received or default
port CoS value and the CoS-to-DSCP map.
port CoS value and the CoS-to-DSCP map.
•
dscp—QoS derives the DSCP value by using the DSCP value from
the ingress packet. For non-IP packets that are tagged, QoS derives
the DSCP value by using the received CoS value; for non-IP
packets that are untagged, QoS derives the DSCP value by using
the default port CoS value. In either case, the DSCP value is
derived from the CoS-to-DSCP map.
the ingress packet. For non-IP packets that are tagged, QoS derives
the DSCP value by using the received CoS value; for non-IP
packets that are untagged, QoS derives the DSCP value by using
the default port CoS value. In either case, the DSCP value is
derived from the CoS-to-DSCP map.
•
ip-precedence—QoS derives the DSCP value by using the IP
precedence value from the ingress packet and the
IP-precedence-to-DSCP map. For non-IP packets that are tagged,
QoS derives the DSCP value by using the received CoS value; for
non-IP packets that are untagged, QoS derives the DSCP value by
using the default port CoS value. In either case, the DSCP value is
derived from the CoS-to-DSCP map.
precedence value from the ingress packet and the
IP-precedence-to-DSCP map. For non-IP packets that are tagged,
QoS derives the DSCP value by using the received CoS value; for
non-IP packets that are untagged, QoS derives the DSCP value by
using the default port CoS value. In either case, the DSCP value is
derived from the CoS-to-DSCP map.
For more information, see the
.
Step 18
set {dscp new-dscp | ip precedence
new-precedence}
new-precedence}
Classify IP traffic by setting a new value in the packet.
•
For dscp new-dscp, enter a new DSCP value to be assigned to the
classified traffic. The range is 0 to 63.
classified traffic. The range is 0 to 63.
•
For ip precedence new-precedence, enter a new IP-precedence
value to be assigned to the classified traffic. The range is 0 to 7.
value to be assigned to the classified traffic. The range is 0 to 7.
Step 19
service-policy policy-map-name
Specify the interface-level policy-map name (from Step 10) and
associate it with the VLAN-level policy map.
associate it with the VLAN-level policy map.
If the VLAN-level policy map specifies more than one class, each class
can have a different service-policy policy-map-name command.
can have a different service-policy policy-map-name command.
Step 20
exit
Return to policy-map configuration mode.
Step 21
exit
Return to global configuration mode.
Step 22
interface interface-id
Specify the SVI to which to attach the hierarchical policy map, and
enter interface configuration mode.
enter interface configuration mode.
Command
Purpose