Panasonic WJ-SX150A Manuel D’Utilisation
62
● Alarm Settings
The operation parameters when an alarm is input to the unit
are configurable.
are configurable.
• Alarm mode: The operation mode activated along with
an alarm input is configurable. Sequence mode or hold
mode is selectable. Alarm mode can be set to OFF
when not using it.
mode is selectable. Alarm mode can be set to OFF
when not using it.
• Alarm event: The sequence number or spot camera is
selectable for the alarm event.
• Alarm input (Alarm port): The alarm polarity (N. O. or N.
C.) is assignable to each alarm input terminal.
• It is also selectable whether to activate the recording
and sequence/spot image monitoring when an alarm
signal is input to the unit. Alarm recording without the
sequence/spot image monitoring is also available.
signal is input to the unit. Alarm recording without the
sequence/spot image monitoring is also available.
● Operator Settings
If you control this unit with a terminal-mode system con-
troller, your operator information, controllable monitors and
auto log-in/log-out will be registrable and configurable.
troller, your operator information, controllable monitors and
auto log-in/log-out will be registrable and configurable.
• Operator registration: Up to 16 operators are available.
ID and password for operator identification are config-
urable. Level and priority can be assigned to each
operator. Each camera's control coverage is also con-
figurable.
urable. Level and priority can be assigned to each
operator. Each camera's control coverage is also con-
figurable.
• Level table: Restriction level for each password is cus-
tomizable.
• Monitor select (Monitor selection): Controllable monitor
can be assigned to each controller.
• Auto login/logout (Auto log-in/log-out): Auto log-in/log-
out is configurable for each controller.
Notes:
• These settings (except Operator registration) are con-
figurable only through WJ-SX150A Administrator
Console. Operator registration is configurable through
SETUP MENU and WJ-SX150A Administrator Console.
Console. Operator registration is configurable through
SETUP MENU and WJ-SX150A Administrator Console.
• When you control the unit with a PS·Data system con-
troller, the above settings will be invalid. Refer to the
system controller's operating instructions.
system controller's operating instructions.
● System Settings
SETUP MENU can configure the clock (time and date),
cable compensation and camera title.
Besides these settings, WJ-SX150A Administrator Console
can select the data ports' baud rates.
cable compensation and camera title.
Besides these settings, WJ-SX150A Administrator Console
can select the data ports' baud rates.
• Clock (Time and date): The unit's time and date are
configurable.
• Cable compensation: Cable compensation type is
selectable depending on the distance between a cam-
era and the unit. It is also possible to determine whether
to send the VD2 timing pulse or control data with the
camera output signals.
era and the unit. It is also possible to determine whether
to send the VD2 timing pulse or control data with the
camera output signals.
• Camera title: Camera title is configurable to identify the
camera images on the monitor. WJ-SX150A
Administrator Console can configure the camera title
including original characters.
Administrator Console can configure the camera title
including original characters.
• Data port: Usually, the ports DATA 1 to 3 connect to the
terminal-mode system controllers. RS-485 cameras will
be connectable with the data port configurations
through WJ-SX150A Administrator Console and SETUP
MENU.
When you use the system controllers via the PS·Data
protocol, you need to configure the DATA 4 port setting
through SX150A Admin Console or SETUP MENU.
be connectable with the data port configurations
through WJ-SX150A Administrator Console and SETUP
MENU.
When you use the system controllers via the PS·Data
protocol, you need to configure the DATA 4 port setting
through SX150A Admin Console or SETUP MENU.
• Recorder: The type and unit address of the recorder
are configurable.
• Multiplxer: The parameters of the recorder mode are
configurable. You can set the alarm and normal record-
ing rate. You can also activate/deactivate dynamic
recording, dummy black, and "CAMSW LOSS Rn” indi-
cation. (Rn is a recorder number.)
ing rate. You can also activate/deactivate dynamic
recording, dummy black, and "CAMSW LOSS Rn” indi-
cation. (Rn is a recorder number.)
• Mux camera (Multiplexer) title: Camera titles which are
displayed with multiscreen segments are configurable.
● Setup File Operation
WJ-SX150A Administrator Console can send a configura-
tion file from the PC to this unit. The utility can also send the
file from the unit to the PC for configuration.
tion file from the PC to this unit. The utility can also send the
file from the unit to the PC for configuration.
• Put a file to SX150A: A configuration data is sent from
the PC to the unit.
• Get a configuration data from SX150A: A configuration
data is sent from the unit to the PC.
• Select setup data file: A configuration data is selected
when sending it from the PC to the unit (or from the unit
to the PC.)
to the PC.)
Note: These settings are configurable only through WJ-
SX150A Administrator Console.
● WJ-SX150A Administrator Console
Configuration
The PC-related settings are configurable.
• Account Manager: WJ-SX150A Administrator Console
operators are registrable and changeable.
• Communication (Serial) port: PC's usable communica-
tion port number and its baud rate (communication
speed) are configurable.
speed) are configurable.
MUX
MUX