Wagner SprayTech Finish 250 Manuel D’Utilisation
13
Finish 370 / 250
GB
DISPLAYS AT THE UNIT / CLEANING THE UNIT
8
CLEANING THE UNIT
A clean state is the best method of ensuring operation wi-
thout problems. After you have fi nished spraying, clean the
unit. Under no circumstances may coating material rests dry
and harden in the unit. The cleaning agent used for cleaning
(only with a fl ash point above 21 °C) must be suitable for the
coating material used.
thout problems. After you have fi nished spraying, clean the
unit. Under no circumstances may coating material rests dry
and harden in the unit. The cleaning agent used for cleaning
(only with a fl ash point above 21 °C) must be suitable for the
coating material used.
•
Secure the spray gun, refer to the operating manual of
the spray gun.
the spray gun.
Remove and clean the tip.
•
Unit with suction system
1. Open relief valve
valve position
(circulation) and switch on unit
2. Remove suction tube from the material container, the re-
turn tube remains over the material container.
3. Immerse the suction system into a container fi lled with a
suitable cleaning agent
4. Turn the pressure control valve back in order to set a mini-
mal spraying pressure.
5. Close relief valve,
valve position
(spraying)
6. Pull the trigger guard of the spray gun in order to pump
the remaining coating material from the suction hose,
high-pressure hose and the spray gun into an open con-
tainer (if appropriate, increase the pressure at the pressu-
re control valve slowly in order to obtain a higher material
fl ow).
high-pressure hose and the spray gun into an open con-
tainer (if appropriate, increase the pressure at the pressu-
re control valve slowly in order to obtain a higher material
fl ow).
The container must be earthed in case of
coating materials which contain solvents.
coating materials which contain solvents.
Caution! Do not pump or spray in container
with small opening (bunghole)!
See safty regulations.
with small opening (bunghole)!
See safty regulations.
7. Open relief valve
valve position
(circulation)
8. Pump suitable cleaning agent in the circuit for several mi-
nutes.
with infl exible suction system (tube) step 9 up to 17
9. Screw the spray gun to the suction tube with both enclo-
9. Screw the spray gun to the suction tube with both enclo-
sed 22 mm wrenches.
10. Pump a suitable cleaning agent in the circuit for about
1 minute.
11. Pull the trigger guard of the spray gun and lock it with a
clamp.
12. Close relief valve,
valve position
(spraying)
13. Clean the suction tube about 3 minutes long.
14. Rinse in the circuit – Open relief valve
valve position
(circulation).
15. Close the spry gun.
16. When cleaning with water repeat the procedure about 3
16. When cleaning with water repeat the procedure about 3
minutes long with clear water.
17. Remove spray gun from suction tube, close spray gun
connection at suction tube with closure nut.
The cleaning eff ect is increased by alterna-
tively opening and closing the spray gun.
tively opening and closing the spray gun.
18. Close relief valve,
valve position
(spraying)
19. Pump the remaining cleaning agent into an open contai-
ner until the pump is empty.
20. Switch off the unit
Warm water improves the cleaning eff ect in
the case of water-dilutable coating materials.
the case of water-dilutable coating materials.
•
Unit with upper hopper
1. Open relief valve
valve position
(circulation) and switch on unit
2. Turn the pressure control valve back in order to set a mini-
mal spraying pressure.
3. Close relief valve,
valve position
(spraying)
4. Pull the trigger guard of the spray gun in order to pump
the remaining coating material from the hopper, high-
pressure hose and the spray gun into an open container (if
appropriate, increase the pressure at the pressure control
valve slowly in order to obtain a higher material fl ow).
pressure hose and the spray gun into an open container (if
appropriate, increase the pressure at the pressure control
valve slowly in order to obtain a higher material fl ow).