Fisher & Paykel V3 DD603 Manuel D’Utilisation

Wooden Chopping Board 

Drill & No.2 Phillips Bit

Tape Measure 

No.2 Phillips Screwdriver

Spirit Level 

Flat Screwdriver

Safety Glasses 

Adjustable Wrench or M5 Socket

Utility Knife 

Ø1

1

/

2

” (38mm) Hole Saw

Pencil Side 

Cutting 

Pliers

Sandpaper

SPARE PARTS INSTALLATION KIT FOR SINGLE & DOUBLE MODELS: p/n 526676

A)  The switched power outlet must be outside the DishDrawer®        
 

cavity so that it is accessible after installation.

B)  The switched power outlet must be between 6” (150mm) and 
 

18” (450mm) from the DishDrawer® cavity.

C)  Refer to Page 9, Step 5 for electrical connection options.

A)  A readily accessible valve must be installed in the water supply pipe.
B)  If the supply pressure exceeds 145 psi (1000kPa), then a pressure 
 

limiting valve must be used.

C)  Review Plumbing Options on pages 4 or 6.  Choose a method that best 
 

suits your needs.

D)  A Drain Hose extension Kit P/N 525798 will extend the drain hoses 
 by 

141

3

/

4

” (3.6m).  The kit is available from the nearest Fisher&Paykel 

 

Authorized Service Agent.  DO NOT extend beyond this limit.

E)  This Dishwasher’s maximum drain height is 37

1

/

2

” (950mm).

A) It is recommended that all cabinetry surrounding the DishDrawer®  
 

(including the underside of the countertop) is sealed with an oil based 

 

paint or moisture-proof polyurethane to prevent possible steam 

 

damage.  The air in the cavity can get very hot and humid (saturated 

 at 

122

o

F/50

o

C)

B)  The self-adhesive moisture protection tape must be applied to the 
 

underside of the countertop to prevent moisture damage, (refer to 

 

cavity diagram pg 3 or 5).  Be sure surfaces are dry and dust-free 

 

prior to application.

C)  Be sure the cavity provides sufficient material to secure the DishDrawer® 
 

using the mounting tabs (refer to step 1, page 7).  If there is  

 

nothing to screw to, add a brace.  See page 3 or 5 for screw locations.

D)  The services hole MUST be immediately adjacent to the rear lower 
 

corner of the cabinetry.  If not, the hoses will prevent the 

 

DishDrawer® being pushed back into the cavity all the way.  The hole 

 

can be located on either side depending on the location of the 

 services.
E)  Be sure the cavity sides are plumb (vertical) as this will assist with 
 levelling 

the 

DishDrawer® 

.

F) Minimum 

clearances:

A)  Care should be taken when the appliance is installed or 
 

removed to reduce the likelihood of damage to the power  

 supply 

cord.

B)  If the power supply cord is damaged, it must be replaced by  
 

the Manufacturer, Service Agent or a similarly qualified person

 

in order to avoid a hazard.

A)  This appliance must be grounded.  In the event of malfunction or 
 

breakdown, grounding will reduce the risk of electric shock by 

 

providing a path of least resistance for electric current.

Improper connection of the equipment-grounding conductor can result 
in a risk of electric shock.  Check with a qualified electrician or 
service representative if you are in doubt as to whether the appliance 
is properly grounded.
B)  This appliance is equipped with a power supply cord having an 
 

equipment-grounding conductor and an earthing plug.  The power 

 

supply plug must be plugged into an appropriate outlet that is installed 

 

and earthed in accordance with all local Codes and Ordinances.

1

/

8

” 

(2.5mm) 

1

/

8

” 

(2.5mm) 

1

/

2

” 

(13mm)