Aussie 3 ELITE Manuel D’Utilisation
4) Turn the adjusting knob clockwise to secure LP
cylinder inside support bracket. (FIG. 13A)
12
FIG. 10A
FIG. 10B
5) Remove the protective cap from the LP cylinder valve.
(Save cap for re-capping.) Make sure all control Knobs
are turned “OFF”. Hold Regulator in a straight line
with LP cylinder valve so the connection does not
cross thread. Insert Regulator Nipple into the LP
cylinder valve. Hand tighten coupling nut in clockwise
direction. Do not use tools. (FIG. 10B)
are turned “OFF”. Hold Regulator in a straight line
with LP cylinder valve so the connection does not
cross thread. Insert Regulator Nipple into the LP
cylinder valve. Hand tighten coupling nut in clockwise
direction. Do not use tools. (FIG. 10B)
Disconnecting LP gas cylinder:
1) Turn all control knobs to the “off” position and turn the
handle on the LP gas cylinder clockwise until it stops.
2) Turn coupling nut on regulator counter-clockwise until
regulator is released from the threaded LP cylinder gas
nozzle.
nozzle.
3) Replace the protective cap over LP cylinder gas
nozzle.
To reduce the risk of serious bodily injury or death:
· This installation must conform with local codes or, in
the absence of local codes, with either the National
Fuel Gas Code, ANSI Z223.1/NFPA 54 Natural Gas and
Propane Installation Code, CSA B149.1, or Propane
Storage and Handling Code, B149.2 or the Standard for
Recreational Vehicles, ANSI A 119.2/NFPA 1192 and
CSA Z240 RV Series, recreational Vehicle Code, as
applicable.
Fuel Gas Code, ANSI Z223.1/NFPA 54 Natural Gas and
Propane Installation Code, CSA B149.1, or Propane
Storage and Handling Code, B149.2 or the Standard for
Recreational Vehicles, ANSI A 119.2/NFPA 1192 and
CSA Z240 RV Series, recreational Vehicle Code, as
applicable.
· If an external electrical source is utilized, the outdoor
cooking appliance, when installed, must be electrically
grounded in accordance with local codes or, in the
absence of local codes, with the National Electrical
Codes, ANSI/NFPA 70, or the Canadian Electrical Code
CSA C22.1.
grounded in accordance with local codes or, in the
absence of local codes, with the National Electrical
Codes, ANSI/NFPA 70, or the Canadian Electrical Code
CSA C22.1.
· Keep any electrical supply cord away from any heated
surfaces.
BEFORE USING YOUR LP GAS GRILL
INSTALLATION CODES
To reduce the risk of serious bodily injury or death:
· This outdoor cooking appliance shall be used only
outdoors and shall not be used in a building, garage,
or any other enclosed area. Locate outdoor cooking
appliance in an area with good ventilation on a level
stable surface clear of combustible and flammable
material.
or any other enclosed area. Locate outdoor cooking
appliance in an area with good ventilation on a level
stable surface clear of combustible and flammable
material.
· Maintain minimum clearances of 36” from back and
sides of grill to any combustible construction.
· Do not locate this appliance under overhead
unprotected combustible construction.
· This outdoor cooking appliance is not intended to be
used in or on boats or installed in or on recreational
vehicles.
vehicles.
· Do not use gas grill as a space heater.
SELECTING A LOCATION
PERFORMING A LEAK TEST
To reduce the risk of serious bodily injury or death:
· Perform a leak test before each use and each time a
gas connection or disconnection is done .
· Perform a leak test in a well ventilated area.
· Never use an open flame to test for gas leaks.
· Never smoke near the grill during a leak test.
· Do not perform a leak test on a grill while it is hot or in
· Never use an open flame to test for gas leaks.
· Never smoke near the grill during a leak test.
· Do not perform a leak test on a grill while it is hot or in
use.
· Do not use the gas grill if you detect a gas leak that
cannot be corrected by using the leak test procedures.
OPERATING AND MAINTINING
YOUR LP GAS GRILL