GTO GP-SW050 Manuel D’Utilisation

1  

(Typically for use with doorbell button or hardwired key pad)

•  Each activation at this input will cycle the operation as follows:

 ….→ OPEN → STOP → CLOSE → STOP → OPEN → …

(Typically for use with photo beam device, loop detector

 

or other non-contact sensors)

•  Activation of this input while the gate is closing will cause the gate to  

  stop and return to the opened position.

•  Activation of this input while the gate is opening has no effect (gate  

 will continue to open).

•  Activation of this input while gate is idle will prevent gate from closing.

(Typically for use with loop detector device)

•  This input is only monitored when the gate is at the fully open

 position. At any other position, activation of this input has no effect on

  gate operation.

•  Activation of this input while gate at the fully open position will

 

  prevent gate from closing.

(Typically for use with safety edge device)

•  Activation of this input while the gate is opening will cause the gate to

  stop and reverse direction for approximately 2 seconds.

•  Activation of this input while the gate is closing has no effect (gate

 will continue to close).

•  Activation of this input while gate is idle will prevent gate from opening.

(Typically for use with safety edge device)

•  Activation of this input while the gate is closing will cause the gate to  

  stop and reverse direction for approximately 2 seconds.

•  Activation of this input while the gate is opening has no effect (gate will continue to open).

•  Activation of this input while gate is idle will prevent gate from closing.

(Typically for use with exit loop or wand)

•  Activation of this input will open the gate if it’s not already at the open position

•  Activation of this input while at open limit will restart the auto close time (if enabled).

(Typically for use with 3-button control station)

•  Activation of this input will close the gate if it is idle AND not already at the closed position.

•  Activation of this input while gate is opening will stop the gate.

(For use with 3-button control station that has ‘NORMALLY CLOSED’ STOP button)

•  Activation of this input will stop the gate.

•  Jumper ‘W1’ must be cut when using normally closed ‘STOP’ button.

•  A normally closed button must be connected to ‘STOP’ and ‘COM’ in order for gate to operate.

  Circuit common (reference for all accessory inputs)

•  Three (3) terminals to provide extra common connection point.

O

N

LOCK

COM

COM

COM

CYCLE

SAFETY

SHADOW

OPEN

CLOSE

STOP

OPEN

EDGE
CLOSE

EDGE

STATUS

DUAL

LINK

GTO   LOOP   DETECTORS

LIMIT   SENSORS

DIAG.
 PORT

BLDC  SPEED  CONTROL

EXIT          SHADOW      SAFETY

AT OPEN

LIMIT

PRISON

MODE

RUNNING

GTO Inc. Tallahassee, FL

SX4000  Logic   Board   Rev.  E

MIN

MAX

MIN

MAX

OFF

120

CLOSED

LED11

LED10

LED09

+  ACC.  PWR.

12VDC

-  300ma

A

C

C.

 PO
WER  

        DU

AL C

ABLE

+12Vdc

COM

DUAL LINK

LINK COM

REL
AY OUTPUT

S

LOCK N.C.

LOCK COM

LOCK N.O.

RUN 1

RUN 2

CLOSED 1

CLOSED 2

CYCLE

SAFETY

OPEN EDGE

CLOSE EDGE

OPEN

CLOSE

STOP

COM

COM

COM

SHADOW

LOOP

1

2

3

4

5

8

9

6

7

NOTE: 

•  All control inputs are dry-contact, normally open, inputs except for #8. DO NOT apply external voltage  

•  All inputs are connected with respect to

 terminal.

•  All inputs have a corresponding LED indicator for diagnostic purposes. All input LED indicators, except for the

 

, will be dimly lit when its corresponding input is inactive and brightly lit when it is activated.