Philips HDR3700/05 Manuel D’Utilisation
83
EN
Program the tuner to scan analogue channels
available in your area.
available in your area.
1
In stop mode, press [HOME]. After
pressing [HOME], the message
“Time Shift Buffer will be cleared
depending on your selection. Do you
want to continue?” will appear.
Select “Yes”.
pressing [HOME], the message
“Time Shift Buffer will be cleared
depending on your selection. Do you
want to continue?” will appear.
Select “Yes”.
2
Select “General Settings” using
[
[
U \ D], then press [OK].
“General Settings” menu will appear.
3
Select “Channel” using [
U \ D],
then press [OK].
4
Select “Analog Channel Setup”
using [
using [
U \ D], then press [OK].
5
Select “Auto Tuning” using [
U \ D],
then press [OK].
The unit will start storing channels available in
your area.
your area.
Wait for several minutes to finish channel storing.
• Analogue channels will be stored in channel 01-
• Analogue channels will be stored in channel 01-
99 after it is scanned by this unit.
6
Press [HOME] to exit.
You can select only the channels stored in this
unit by using [PROGRAM + / –].
unit by using [PROGRAM + / –].
To cancel auto tuning
Press [BACK
Press [BACK
U] or [HOME] during scanning.
Note
• The selection will be affected by how you receive TV
channels in your local area.
• If the auto tuning is cancelled during scanning,
some channels not yet tuned may not be received.
• You cannot change the channel when this unit is in
any recording mode (normal recording, One-touch
Timer Recording or timer recording).
Timer Recording or timer recording).
You can manual tune to and set each analogue
channel.
channel.
1
In stop mode, press [HOME]. Select
“General Settings” using [
“General Settings” using [
U \ D],
then press [OK].
2
Select “Channel” using [
U \ D],
then press [OK].
3
Select “Analog Channel Setup”
using [
using [
U \ D], then press [OK].
4
Select “Manual Tuning” using
[
[
U \ D], then press [OK].
5
Select “Position” using [
U \ D],
then press [
P].
6
Select the position number you want
to use using [Alphanumeric keypad]
or [
to use using [Alphanumeric keypad]
or [
U \ D], then press [L].
• You can select position number 01-99.
7
Select “Channel” using [
U \ D],
then press [
P].
8
Press [
U \ D] to start scanning.
• The tuner will begin to search up or down
automatically. When a channel is found, the unit
will stop searching and the picture will appear
on the TV screen.
will stop searching and the picture will appear
on the TV screen.
• You can select a desired channel number using
[Alphanumeric keypad]. Refer to the following
Channel Plan table and press the three digits to
select the channel number.
(To select channel 4, press [0] first and then
press [4].) Or press [4] and then wait for 2
seconds after “--4” appears.
Channel Plan table and press the three digits to
select the channel number.
(To select channel 4, press [0] first and then
press [4].) Or press [4] and then wait for 2
seconds after “--4” appears.
• If this is the channel you want, press [
L].
Auto Tuning (ANALOG)
ANALOG
General Settings
Channel
Digital&Analog Tuning
Digital&Analog Tuning
Digital Channel Setup
Analog Channel Setup
Auto Tuning
Manual Tuning
Sort Channels
Analog Channel Setup
Manual Tuning (ANALOG)
ANALOG
Channel Plan
CH Indication
TV Channel
01 – 10
IRA-IRJ, GAP
21 – 69
E21 – E69
74 – 78
X, Y, Z, Z+1, Z+2
80 – 99, 100
S1 – S20, GAP
121 – 141
S21 – S41
01
2
2
General Settings
Analog Channel Setup
Position
ON
Channel
Decoder
Skip
Manual Tuning
OFF
In
trod
ucti
on
Con
n
ec
ti
ti
on
s
s
In
iti
al
Setup
P
layb
ack
Edi
tin
g
O
thers
General Settings
Reco
rdi
n
n
g
E2N41BN_EN.book Page 83 Wednesday, July 2, 2008 4:36 PM