Snapper LE3190E Manuel D’Utilisation
8
Section 2 - OPERATING INSTRUCTIONS
2.2.4. STOPPING
Stop the auger by releasing the auger control. Stop
the engine by turning the key switch to the “OFF”
position. Always remove key from key switch
before leaving machine unattended. See
Figure 2.7.
Stop the auger by releasing the auger control. Stop
the engine by turning the key switch to the “OFF”
position. Always remove key from key switch
before leaving machine unattended. See
Figure 2.7.
FIGURE 2.7
2.2 STARTING, STOPPING & OPERATION
(ELECTRIC START MODELS)
(Go to Page 7 for Recoil Start Models)
2.2.5. ENGINE & AUGER
2.2.5. ENGINE & AUGER
WARNING
DO NOT use an electrical extension cord that is
damaged. A damaged electrical extension cord
could cause a shock or fire. Thoroughly inspect
electrical extension cord before using machine. If
cord is damaged, do not use and do not operate
machine. Replace damaged cord immediately.
Contact your SNAPPER service dealer for
assistance. To reduce the risk of electric shock, use
only with an extension cord intended for outdoor
use having a cord type: SW-A, SOW-A, STW-A,
STOW-A, SJW-A, SJTW-A or SJTOW-A.
damaged. A damaged electrical extension cord
could cause a shock or fire. Thoroughly inspect
electrical extension cord before using machine. If
cord is damaged, do not use and do not operate
machine. Replace damaged cord immediately.
Contact your SNAPPER service dealer for
assistance. To reduce the risk of electric shock, use
only with an extension cord intended for outdoor
use having a cord type: SW-A, SOW-A, STW-A,
STOW-A, SJW-A, SJTW-A or SJTOW-A.
1. Connect the power cord to the starter switch box
on machine’s control panel then plug the other end
into 120 volt AC receptacle.
2. Turn ignition key to the “ON” position.
3. Move choke control to the choke “ON” position.
See Figure 2.8.
4. Push primer button three times to start a cold
engine. NOTE: Do not use primer button to start
warm engine.
5. Push the electric starter button. DO NOT hold
button for more than 20 seconds to avoid damaging
the starting motor. See Figure 2.8.
6. After engine starts, move the choke control to the
no choke “OFF” position. Allow a brief warm-up until
engine runs smooth.
7. Disconnect power cord from AC receptacle.
Disconnect power cord from machine and remove
cord from area where machine will be in operation.
on machine’s control panel then plug the other end
into 120 volt AC receptacle.
2. Turn ignition key to the “ON” position.
3. Move choke control to the choke “ON” position.
See Figure 2.8.
4. Push primer button three times to start a cold
engine. NOTE: Do not use primer button to start
warm engine.
5. Push the electric starter button. DO NOT hold
button for more than 20 seconds to avoid damaging
the starting motor. See Figure 2.8.
6. After engine starts, move the choke control to the
no choke “OFF” position. Allow a brief warm-up until
engine runs smooth.
7. Disconnect power cord from AC receptacle.
Disconnect power cord from machine and remove
cord from area where machine will be in operation.
NOTE: Stop the auger by releasing the auger control.
Stop the engine by turning the key switch to the “OFF”
position.
position.
FIGURE 2.8
RELEASE AUGER
CONTROL TO
STOP AUGER
CONTROL TO
STOP AUGER
TURN KEY TO THE “OFF”
POSITION TO STOP ENGINE
POSITION TO STOP ENGINE
PUSH STARTER
BUTTON
BUTTON
PUSH PRIMER
THREE TIMES
THREE TIMES
INSERT POWER CORD
INTO STARTER BOX
INTO STARTER BOX
(SHOWN IN “OFF POSITION)
TURN KEY TO THE “ON”
POSITION
TURN KEY TO THE “ON”
POSITION
(SHOWN IN “OFF POSITION)
MOVE CHOKE TO THE “ON”
POSITION
MOVE CHOKE TO THE “ON”
POSITION