Alcatel-Lucent 6850-48 Guide De Réglage Du Réseau
Configuring IP
IP Forwarding
OmniSwitch AOS Release 6 Network Configuration Guide
September 2009
page 24-11
Creating a Static Route
Static routes are user-defined and carry a higher priority than routes created by dynamic routing proto-
cols. That is, if two routes have the same metric value, the static route has the higher priority. Static routes
allow you to define, or customize, an explicit path to an IP network segment, which is then added to the IP
Forwarding table. Static routes can be created between VLANs to enable devices on these VLANs to
communicate.
cols. That is, if two routes have the same metric value, the static route has the higher priority. Static routes
allow you to define, or customize, an explicit path to an IP network segment, which is then added to the IP
Forwarding table. Static routes can be created between VLANs to enable devices on these VLANs to
communicate.
Use the
command to create a static route. You must specify the destination IP address of
the route as well as the IP address of the first hop (gateway) used to reach the destination. For example, to
create a static route to IP address 171.11.0.0 through gateway 171.11.2.1, you would enter:
create a static route to IP address 171.11.0.0 through gateway 171.11.2.1, you would enter:
-> ip static-route 171.11.0.0 gateway 171.11.2.1
The subnet mask is not required if you want to use the natural subnet mask. By default, the switch imposes
a natural mask on the IP address. In the above example, the Class B mask of 255.255.0.0 is implied. If you
do not want to use the natural mask, you must enter a subnet mask. For example, to create a static route to
IP address 10.255.11.0, you would have to enter the Class C mask of 255.255.255.0:
a natural mask on the IP address. In the above example, the Class B mask of 255.255.0.0 is implied. If you
do not want to use the natural mask, you must enter a subnet mask. For example, to create a static route to
IP address 10.255.11.0, you would have to enter the Class C mask of 255.255.255.0:
-> ip static-route 10.255.11.0 mask 255.255.255.0 gateway 171.11.2.1
Note that specifying the length of the mask in bits is also supported. For example, the above static route is
also configurable using the following command:
also configurable using the following command:
-> ip static-route 10.255.11.0/24 gateway 171.11.2.1
When you create a static route, the default metric value of 1 is used. However, you can change the prior-
ity of the route by increasing its metric value. The lower the metric value, the higher the priority. This
metric is added to the metric cost of the route. The metric range is 1 to 15. For example:
ity of the route by increasing its metric value. The lower the metric value, the higher the priority. This
metric is added to the metric cost of the route. The metric range is 1 to 15. For example:
-> ip static-route 10.255.11.0/24 gateway 171.11.2.1 metric 5
Static routes do not age out of the IP Forwarding table; you must delete them from the table. Use the
no ip static route command to delete a static route. You must specify the destination IP address of the
route as well as the IP address of the first hop (gateway). For example, to delete a static route to IP address
171.11.0.0 through gateway 171.11.2.1, you would enter:
no ip static route command to delete a static route. You must specify the destination IP address of the
route as well as the IP address of the first hop (gateway). For example, to delete a static route to IP address
171.11.0.0 through gateway 171.11.2.1, you would enter:
-> no ip static-route 171.11.0.0 gateway 171.11.2.1
The IP Forwarding table includes routes learned through one of the routing protocols (RIP, OSPF, BGP)
as well as any static routes that are configured. Use the
as well as any static routes that are configured. Use the
Forwarding table.
Note. A static route is not active unless the gateway it is using is active.