Alcatel-Lucent 6850-48 Guide De Réglage Du Réseau
Configuring Ethernet Ports
Setting Ethernet Parameters for Non-Combo Ports
OmniSwitch AOS Release 6 Network Configuration Guide
September 2009
page 1-19
Configuring Crossover Settings
To configure crossover settings on a single port, a range of ports, or an entire slot, use the
are not accepted.
Setting the crossover configuration to auto will configure the interface or interfaces to automatically
detect crossover settings. Setting crossover configuration to mdix will configure the interface or inter-
faces for MDIX (Media Dependent Interface with Crossover), which is the standard for hubs and switches.
Setting crossover to mdi will configure the interface or interfaces for MDI (Media Dependent Interface),
which is the standard for end stations.
detect crossover settings. Setting crossover configuration to mdix will configure the interface or inter-
faces for MDIX (Media Dependent Interface with Crossover), which is the standard for hubs and switches.
Setting crossover to mdi will configure the interface or interfaces for MDI (Media Dependent Interface),
which is the standard for end stations.
To configure crossover settings on an entire switch, enter interfaces, followed by the slot number, cross-
over, and the desired setting. For example, to set the crossover configuration to auto on slot 2, enter:
over, and the desired setting. For example, to set the crossover configuration to auto on slot 2, enter:
-> interfaces 2 crossover auto
To configure crossover settings on a single port, enter interfaces, followed by the slot number, a slash (/),
the port number, crossover, and the desired setting. For example, to set the crossover configuration to auto
on port 3 on slot 2, enter:
the port number, crossover, and the desired setting. For example, to set the crossover configuration to auto
on port 3 on slot 2, enter:
-> interfaces 2/3 crossover auto
To configure crossover settings on a range of ports, enter interfaces, followed by the slot number, a slash
(/), the first port number, a hyphen (-), the last port number, crossover, and the desired setting. For exam-
ple, to set the crossover configuration to auto on ports 1 through 3 on slot 2, enter:
(/), the first port number, a hyphen (-), the last port number, crossover, and the desired setting. For exam-
ple, to set the crossover configuration to auto on ports 1 through 3 on slot 2, enter:
-> interfaces 2/1-3 crossover auto
Configuring Flow Control on Non-Combo Ports
command is used to configure end-to-end (E2E) flow control (pause) settings for
non-combo ports that run in full duplex mode. Configuring flow control is done to specify whether or not
an interface will transmit, honor, or both transmit and honor PAUSE frames. PAUSE frames are used to
temporarily pause the flow of traffic between two connected devices to help prevent packet loss when traf-
fic congestion occurs between switches.
an interface will transmit, honor, or both transmit and honor PAUSE frames. PAUSE frames are used to
temporarily pause the flow of traffic between two connected devices to help prevent packet loss when traf-
fic congestion occurs between switches.
Using the interfaces pause command alone is sufficient to configure E2E flow control on a 24-port
OmniSwitch 6400, a 24-port OmniSwitch 6850 and an OmniSwitch 6855 running in standalone mode.
However, if a switch is a 48-port switch running in standalone mode, then a flow control VLAN is
required in addition to enabling flow control. This type of VLAN is configured using the
OmniSwitch 6400, a 24-port OmniSwitch 6850 and an OmniSwitch 6855 running in standalone mode.
However, if a switch is a 48-port switch running in standalone mode, then a flow control VLAN is
required in addition to enabling flow control. This type of VLAN is configured using the
command.
Although E2E flow control is only supported on standalone OmniSwitch 6400, OmniSwitch 6850, and
OmniSwitch 6855 switches, it is possible to configure a stack of switches or a chassis-based switch to
honor PAUSE frames only. This is also done with the interfaces pause command.
OmniSwitch 6855 switches, it is possible to configure a stack of switches or a chassis-based switch to
honor PAUSE frames only. This is also done with the interfaces pause command.
Note that if autonegotiation and flow control are both enabled for an interface, then autonegotiation deter-
mines how the interface will process PAUSE frames. See
mines how the interface will process PAUSE frames. See
for more information. If autonegotiation is disabled but flow control is enabled, then the config-
ured flow control settings apply.
By default, flow control is disabled. To configure flow control for one or more ports, use the interfaces
pause command with one of the following parameters to specify how PAUSE frames are processed:
pause command with one of the following parameters to specify how PAUSE frames are processed:
• tx—Transmit PAUSE frames to peer switches when traffic congestion occurs on the local interface. Do
not honor PAUSE frames from peer switches.