Fantom Drives fddrwu2p20d Manuel Du Matériel Informatique
My computer will not recognize the drive
Make sure the software for your drive is installed, following the instructions in this man-
ual. Disconnect the drive and power the unit off. Wait 15 seconds, then power your
drive back on. Wait 5 more seconds, then reconnect the drive to your computer system.
ual. Disconnect the drive and power the unit off. Wait 15 seconds, then power your
drive back on. Wait 5 more seconds, then reconnect the drive to your computer system.
When I try to burn CDs, I get a “Sense Key” error or other burning failures
This is usually caused by burning at faster speed than the media allows. Make sure the
media you are writing to is compatible with the speed you are trying to burn. Here are
some suggestions to successful burning: try lowering the burn speed down and if you
are burning to CD-R media; choose “Write CD” option instead of the “Write Session”
option; Increase the Disk buffer size in the CD Burning application.
media you are writing to is compatible with the speed you are trying to burn. Here are
some suggestions to successful burning: try lowering the burn speed down and if you
are burning to CD-R media; choose “Write CD” option instead of the “Write Session”
option; Increase the Disk buffer size in the CD Burning application.
My DVD burns keep failing. Why?
There are many brands of DVD media, not all of which are compatible with all DVD
mechanisms. Please try a different brand of media, and check with
mechanisms. Please try a different brand of media, and check with
www.MicroNet.com
for the latest compatibility information.
Can I use my USB CDRW/DVD-RW through a USB hub?
Yes, As long as the hub is a powered hub since bus powered hubs do not work with
mass storage devices. For best results, MicroNet recommends running directly off of the
USB port on the computer
mass storage devices. For best results, MicroNet recommends running directly off of the
USB port on the computer
The computer will not boot from a FireWire or USB CD
Booting from USB or Firewire is currently supported on some PCs with supported BIOS.
Please check your motherboard’s vendor website for the latest information and updates.
Please check your motherboard’s vendor website for the latest information and updates.
Sonic MediaSuite does not install properly
This could happen for a number of reasons. Try the following solutions:
1. Insufficient permissions on the machine. If you are using a Windows 2000 machine,
1. Insufficient permissions on the machine. If you are using a Windows 2000 machine,
you need to have administrative permission to run an InstallShield Professional 6.x
setup. Make sure you have the correct permissions.
setup. Make sure you have the correct permissions.
2. Check and make sure Ikernel.exe is not in memory. If it is, and setup is not run-
ning at the time, end that task.
4. Clean out the Temp directory.
5. Delete the Program Files\Common Files\InstallShield\Engine folder and then rerun the setup.
6. Reinstalling Internet Explorer (IE) 5.x can also repair a number of corrupted/miss-
5. Delete the Program Files\Common Files\InstallShield\Engine folder and then rerun the setup.
6. Reinstalling Internet Explorer (IE) 5.x can also repair a number of corrupted/miss-
ing core Windows files from your machine, so reinstalling IE 5.x is also suggested.
7. If you are trying to install to a Windows 98 machine, download and run
DCom98.exe from the following site:
http://www.microsoft.com/com/dcom/dcom98/download.asp.
http://www.microsoft.com/com/dcom/dcom98/download.asp.
8. Review the readme file on your Sonic MediaSuite CD, located at
\MyDVD\ReadMe\English\Readme.htm
I have a problem not listed on this page
MicroNet offer additional troubleshooting resources on our website at
www.MicroNet.com/support/faqs
. If the problem still persists, please call our support
hotline at 310-320-0772.
TROUBLESHOOTING
Please Be sure to turn ON your MicroNet Storage Device before connecting it to your computer
For additional troubleshooting information please visit our website at
www.MicroNet.com
To avoid corruption or loss of data, never disconnect your drive while transferring data
Page 2
Page 7
The following steps must be performed to properly install your drive:
1. Set Drive Jumper Settings
The mode select jumpers are 6 straight angle pins located on
the rear of the DVD-R/-RW Combo drive.. By placing a jumper
on the pins, you can select the ATA device operating Mode:
the rear of the DVD-R/-RW Combo drive.. By placing a jumper
on the pins, you can select the ATA device operating Mode:
Important Note: Disconnect power from your computer system before beginning
installation.
installation.
2. Mount Drive
Remove computer cover and faceplate if required. Refer to your computer system’s manual
for removal information. If the DVD Combo drive is replacing a CD-ROM, remove CD-ROM
presently installed in your system. Place the DVD Combo drive in any free half-height drive
slot at the front of your computer. (It can be mounted horizontally or vertically.)
Carefully start sliding the DVD Combo drive into the opening with the disc tray facing the
front of the computer. Before you push the drive all the way in you will need to connect
the IDE BUS cable, Audio cable and the Power cable on the back of the drive.
Remove computer cover and faceplate if required. Refer to your computer system’s manual
for removal information. If the DVD Combo drive is replacing a CD-ROM, remove CD-ROM
presently installed in your system. Place the DVD Combo drive in any free half-height drive
slot at the front of your computer. (It can be mounted horizontally or vertically.)
Carefully start sliding the DVD Combo drive into the opening with the disc tray facing the
front of the computer. Before you push the drive all the way in you will need to connect
the IDE BUS cable, Audio cable and the Power cable on the back of the drive.
3. Attach IDE BUS Cable
Your computer system should have a primary and secondary
IDE BUS, cable with your Hard Drive most likely being the
Master on the primary BUS. Connect BUS cable as follows,
assuring that pin 1 of cable (side with red stripe) is connected
to pin 1 (closest to the power connector) of the DVD Combo
drive's interface connector. Please remember that each BUS
can only have one master and one slave devices.
Your computer system should have a primary and secondary
IDE BUS, cable with your Hard Drive most likely being the
Master on the primary BUS. Connect BUS cable as follows,
assuring that pin 1 of cable (side with red stripe) is connected
to pin 1 (closest to the power connector) of the DVD Combo
drive's interface connector. Please remember that each BUS
can only have one master and one slave devices.
4. Attach Power Cable
Connect an internal computer power supply cable to the
power socket at the back of the DVD Combo drive. One side
of the plug has chamfered edges, so the power connector fits
only one way. Push plug completely into the socket making
sure the plug fits correctly
Connect an internal computer power supply cable to the
power socket at the back of the DVD Combo drive. One side
of the plug has chamfered edges, so the power connector fits
only one way. Push plug completely into the socket making
sure the plug fits correctly
5. Attach audio cable
If you have a sound card and speakers, and would like to play
audio CDs on your computer, you will need to install a
CD/DVD audio cable. The sound cable connects to your
sound card at one end and the other end connects to the digi-
tal audio connector at the left rear of the DVD Combo drive.
Refer to the instructions that came with your sound card for
details on any sound-driver software required
If you have a sound card and speakers, and would like to play
audio CDs on your computer, you will need to install a
CD/DVD audio cable. The sound cable connects to your
sound card at one end and the other end connects to the digi-
tal audio connector at the left rear of the DVD Combo drive.
Refer to the instructions that came with your sound card for
details on any sound-driver software required
6. Completing the installation
After you have connected all the necessary cables, push the DVD Combo drive completely
into the computer’s drive slot. Mount drive per your computer’s instructions. The screw
length should not exceed 3±0.5mm (measured from outside surface of side or bottom of
drive to tip of screw). Replace computer cover and all outer screws.
After you have connected all the necessary cables, push the DVD Combo drive completely
into the computer’s drive slot. Mount drive per your computer’s instructions. The screw
length should not exceed 3±0.5mm (measured from outside surface of side or bottom of
drive to tip of screw). Replace computer cover and all outer screws.
C
C
S
S
S
S
S
L
L
L
M
M
A
A
MA: Master, default position
SL: Slave configuration
CS: Cable Select configuration
SL: Slave configuration
CS: Cable Select configuration
INSTALLATION- Internal Hardware