Toshiba tdp-tw350u Manuel Du Propriétaire
21
Preparations
20
Operating a computer using the remote control
A computer can be operated using the projector’s remote control. This function is available
on any computer with the Windows 98/98SE, Windows Me, Windows 2000, or Windows XP
OS, that is equipped with a USB port which can support USB1.1 (The mouse remote
control receiver is also supported on OS 9 or OS X for the Macintosh). However, please
note that Toshiba does not guarantee the operation of all computers.
on any computer with the Windows 98/98SE, Windows Me, Windows 2000, or Windows XP
OS, that is equipped with a USB port which can support USB1.1 (The mouse remote
control receiver is also supported on OS 9 or OS X for the Macintosh). However, please
note that Toshiba does not guarantee the operation of all computers.
1
Connecting a computer
Connect the mouse remote control receiver (supplied) to a computer.
Mouse remote control receiver
To USB port
2
Operating a computer
Operate remote control’s buttons towards the mouse remote control receiver.
● Moving the mouse pointer
● Moving the mouse pointer
Press the mouse control button in the direction you wish the mouse pointer to move,
then press.
then press.
● To left click
Press the L-CLICK button.
● To right click
Press the R-CLICK button.
● To drag and drop
Holding down the L-CLICK button, move the mouse control button until the mouse
pointer is over the desired location, then release the L-CLICK button.
pointer is over the desired location, then release the L-CLICK button.
● Using the computer’s page up [↑] and down [↓] function
Press the PAGE+ and PAGE- buttons to switch PowerPoint
®
slides.
The remote control may fail to operate
if the mouse remote control receiver is
exposed to bright sunlight or
fluorescent lighting.
if the mouse remote control receiver is
exposed to bright sunlight or
fluorescent lighting.
In such a case, change position or
direction of the mouse remote control
receiver and retry.
direction of the mouse remote control
receiver and retry.
Mouse control
Remote Control Front
Remote Control Rear
PAGE –
PAGE +
R-CLICK
L-CLICK
EASY SETUP
■ Operating the remote
control
Turn on the ON/OFF switch of the
remote control.
Point toward the projector’s
infrared remote sensor, and press a
button on the remote control.
remote control.
Point toward the projector’s
infrared remote sensor, and press a
button on the remote control.
• Operating the projector from the front
Approx. 15
°
Approx. 5m
• Operating the projector from the rear
Approx. 15
°
Approx. 5m
■ Loading dry-cell batteries
into the remote control
q Remove the battery cover.
w Insert the dry-cell batteries.
Be sure to align the plus and minus
ends of the batteries properly.
ends of the batteries properly.
Two batteries (LR03, SIZE AAA) are
used.
used.
e Replace the battery cover.
Dry-cell batteries
• Before using the batteries, be sure to observe the Safety Precautions described in
previous pages.
• Remove batteries from remote control when not using for extended periods.
• If the remote control stops working, or if its range decreases, replace all the batteries with
• If the remote control stops working, or if its range decreases, replace all the batteries with
new ones.
The remote control
• Turn off the ON/OFF switch of the remote control when not in use or to store in baggage.
• The remote control may fail to operate if the infrared remote sensor is exposed to bright
• The remote control may fail to operate if the infrared remote sensor is exposed to bright
sunlight or fluorescent lighting.
• Do not drop or bang.
• Do not leave in hot or humid locations.
• Do not get wet or place on top of wet objects.
• Do not take apart.
• In rare cases, ambient conditions could impede the operation of the remote control. If this
• Do not leave in hot or humid locations.
• Do not get wet or place on top of wet objects.
• Do not take apart.
• In rare cases, ambient conditions could impede the operation of the remote control. If this
happens, point the remote control at the main unit again, and repeat the operation.
Preparing and using the remote control