Toshiba 32ax60 Manuel Du Propriétaire
12
Setting up
y
our T
V
Using the TV/VIDEO button on the TV
Use the TV/VIDEO button on the TV to monitor or change the signal
source connected to your TV.
To select the signal source:
source connected to your TV.
To select the signal source:
Press the TV/VIDEO button on the TV to select either VIDEO 1,
VIDEO 2, VIDEO 3, ColorStream, ANT 1, or ANT 2.
Repeatedly press the TV/VIDEO button on the TV until the
signal source you wish to use displays in purple.
VIDEO 2, VIDEO 3, ColorStream, ANT 1, or ANT 2.
Repeatedly press the TV/VIDEO button on the TV until the
signal source you wish to use displays in purple.
TO SELECT PUSH TV/VIDEO
ANT 2
VIDEO 2
COLOR
STREAM
STREAM
VIDEO 1
ANT 1
VIDEO 3
Adding channels to the TV’s memory
When you press Channel
▲
or
▼
on the TV or remote control,
the TV stops only on the channels stored in the TV’s memory.
Note: To tune the TV to a channel not programmed in the TV’s
memory, use the Channel Number buttons on the remote control.
Follow the steps below and on the next page to program channels into
the TV’s memory.
Note: To tune the TV to a channel not programmed in the TV’s
memory, use the Channel Number buttons on the remote control.
Follow the steps below and on the next page to program channels into
the TV’s memory.
Programming channels automatically
Your TV can automatically detect all active channels in your area and
store them in the TV’s memory. After the channels are stored auto-
matically, you can manually add or erase individual channels (see page
13. If you use both ANT-1 and ANT-2 terminals, you will need to
program channels for each input source.
store them in the TV’s memory. After the channels are stored auto-
matically, you can manually add or erase individual channels (see page
13. If you use both ANT-1 and ANT-2 terminals, you will need to
program channels for each input source.
To program channels automatically:
1. Press MENU.
2. Press
2. Press
x
or
•
to highlight the SET UP menu.
3. Press
y
or
z
to highlight TV/CABLE.
4. Press
x
or
•
to highlight either TV or CABLE, depending on
which you use. If you use an antenna, highlight TV. If you use
cable, highlight CABLE.
cable, highlight CABLE.
5. Press
z
to highlight CH PROGRAM.
AUDIO
PREFER
SET UP
C.CAPT
PICTURE
[ ]
[ ]
LANGUAGE:
ANT1/2:
TV/CABLE:
CH PROGRAM
ADD/ERASE:
MORE
MOVE SELECT
[ENGLISH]FRANCAIS
ESPANOL
[ANT1]ANT2
[TV]CABLE
[ADD]ERASE
AUDIO
PREFER
SET UP
C.CAPT
PICTURE
[ ]
[ ]
LANGUAGE:
ANT1/2:
TV/CABLE:
CH PROGRAM
ADD/ERASE:
MORE
MOVE START
[ENGLISH]FRANCAIS
ESPANOL
[ANT1]ANT2
[TV]CABLE
[ADD]ERASE
6. Press
x
or
•
to start automatic channel programming. The TV
automatically cycles through every TV or cable channel
(depending on which you selected), and stores all active channels
in the TV’s memory.
(depending on which you selected), and stores all active channels
in the TV’s memory.
7. When automatic channel programming is complete, the message
“CH Programming Completed” appears.
8. Press Channel
▲
or
▼
to view the programmed channels.
CH RTN
ADV/
PIP CH
ADV/
PIP CH
TV
CABLE
LIGHT
MUTE TV/VIDEO TIMER
RECALL
POWER
VCR
CH
VOL
ENT
ENTER
FAV
FAV
EXIT
MENU
RESET
1
4
7
2
5
8
3
6
9
0
100
Menu
Exit
Channel
C.CAPT
TV/Video
Menu
TV/ VIDEO
VOLUME
CHANNEL
TV/Video
MENU