Toshiba cn36z71 Manuel Du Propriétaire
12
Intr
oduction
Connecting
y
our T
V
Using the
Remote Contr
ol
Setting up
y
our T
V
Using the T
V
’s
F
eatur
es
Appendix
Index
1
2
3
4
5
6
7
8
9
ENT
100
0
CH
VOL
POWER
TIMER
RECALL
TV/VIDEO
MUTE
CH RTN
STROBE
EXIT
LIGHT
STOP SOURCE
ADV/
PIP CH
ADV/
PIP CH
FAV
FAV
PLAY PIP
REC
TV/VCR
REW
FF
FAVORITE
MENU/
PREVIEW
ENTER
TV
CABLE
VCR
AUX
AUX
To control a cable TV converter:
Program the remote control to recognize the brand of your
converter. The shaded buttons will control the cable TV
converter.
Set the TV/CABLE/VCR/AUX switch to the CABLE position.
converter. The shaded buttons will control the cable TV
converter.
Set the TV/CABLE/VCR/AUX switch to the CABLE position.
Programming the remote control for use with a
VCR or a cable TV converter
VCR or a cable TV converter
This remote control is pre-programmed to operate Toshiba VCRs. To
use VCRs or cable converters other than Toshiba models, you must
follow the steps below before you operate your remote control.
use VCRs or cable converters other than Toshiba models, you must
follow the steps below before you operate your remote control.
1. Refer to the “VCR code table” or “Cable TV converter code
table” on pages 13-14 to find the number that corresponds to the
brand name of your VCR or converter.
If more than one number is listed, try each one separately until
you find the one that works.
brand name of your VCR or converter.
If more than one number is listed, try each one separately until
you find the one that works.
2. If you are reprogramming the remote control to operate your:
• VCR, set the TV/CABLE/VCR/AUX switch on the remote
control to VCR.
• cable converter, set the TV/CABLE/VCR/AUX switch on
the remote control to CABLE.
3. Hold down the RECALL button while using the Channel
Number buttons to enter the three-digit code number of your
brand of VCR or converter.
The program indicator (LIGHT button) lights up for 1 second
when the programming is completed.
When an operation error has occurred, the indicator blinks.
Press RECALL again to reset.
brand of VCR or converter.
The program indicator (LIGHT button) lights up for 1 second
when the programming is completed.
When an operation error has occurred, the indicator blinks.
Press RECALL again to reset.
4. Point the remote control at the VCR or converter and press
POWER to test the code number.
If the VCR or converter turns on, you have entered the right
number.
If the VCR or converter does not respond to the remote control,
you may have entered the wrong number. Repeat steps 1-4 with
another code number.
If the VCR or converter turns on, you have entered the right
number.
If the VCR or converter does not respond to the remote control,
you may have entered the wrong number. Repeat steps 1-4 with
another code number.
5. Reset the TV/CABLE/VCR/AUX switch to TV to control the
TV.
For future reference, write down the code numbers you used:
VCR code
_____________________
Cable code
_____________________
Note:
• Each time you replace the batteries, you
• Each time you replace the batteries, you
must reprogram the remote control.
• Some newer VCRs are capable of working
on either of two remote codes. These VCRs
have a switch labeled “VCR1/VCR2.”
have a switch labeled “VCR1/VCR2.”
If your VCR has this kind of switch, it may
not respond to any of the code numbers for
your VCR brand name. In this case, set the
switch to the other position (VCR1 or
VCR2) and reprogram the remote control.
not respond to any of the code numbers for
your VCR brand name. In this case, set the
switch to the other position (VCR1 or
VCR2) and reprogram the remote control.
Enter
Channel
yz
Channel
Number
Number
POWER
Program indicator
RECALL