Toshiba 32cv510 Manuel D’Utilisation
29
CV510U (E/F) Web 213:276
Chapter 5: Setting up your TV
Programming channels into the
TV’s channel memory
TV’s channel memory
When you press
< or , on the remote control or TV control
panel, your TV will stop only on the channels you programmed
into the TV’s channel memory.
Follow the steps below to program channels into the TV’s
channel memory.
into the TV’s channel memory.
Follow the steps below to program channels into the TV’s
channel memory.
Programming channels automatically
Your TV can automatically detect all active channels in your
area and store them in its memory. After the channels are
programmed automatically, you can manually add or erase
individual channels in the channel memory.
area and store them in its memory. After the channels are
programmed automatically, you can manually add or erase
individual channels in the channel memory.
Note:
• If the ANT/CABLE input signal type is set to Cable, the
• If the ANT/CABLE input signal type is set to Cable, the
automatic channel programming process erases channels
that were previously programmed into the TV’s memory.
that were previously programmed into the TV’s memory.
• If the ANT/CABLE input signal type is set to Antenna, the
automatic channel programming process adds newly found
channels to the existing set of programmed channels (and
does NOT erase channels that were previously
programmed into the TV’s memory.) To remove an Antenna
source channel from the memory, you must manually delete
it.
channels to the existing set of programmed channels (and
does NOT erase channels that were previously
programmed into the TV’s memory.) To remove an Antenna
source channel from the memory, you must manually delete
it.
• To tune the TV to a channel not programmed in the channel
memory, you must use the Channel Number buttons on the
remote control.
remote control.
• Programming channels when the ANT/CABLE input is
configured for Cable will take substantially longer than when
the ANT/CABLE input is configured for Antenna. This is
normal; however, once channel programming is finished,
you should not have to repeat the programming process
again unless your Cable TV service lineup changes
significantly.
the ANT/CABLE input is configured for Antenna. This is
normal; however, once channel programming is finished,
you should not have to repeat the programming process
again unless your Cable TV service lineup changes
significantly.
To program channels automatically:
1
You must configure the ANT/CABLE input source, if you
have not already done so (
have not already done so (
-
page 28).
2
From the Setup menu, highlight Installation and press
T. A new set of Installation menu icons will appear.
T. A new set of Installation menu icons will appear.
3
Open the Terrestrial menu, highlight Channel
Program to bring up the Start, and press
Program to bring up the Start, and press
T again to
begin channel programming.
The TV will automatically cycle through all the channels,
and store all active channels in the channel memory.
While the TV is cycling through the channels, the
message “Scanning channels, please wait...” appears (as
shown above).
and store all active channels in the channel memory.
While the TV is cycling through the channels, the
message “Scanning channels, please wait...” appears (as
shown above).
4
To cancel channel programming, press
O on the remote
control (or highlight Cancel in the on-screen display and
press
press
T).
When channel programming is finished, press
< or , to
view the programmed channels.
Manually adding and deleting channels
in the channel memory
in the channel memory
After automatically programming channels into the channel
memory, you can manually add or delete individual channels.
memory, you can manually add or delete individual channels.
To add or delete channels in the channel memory:
1
From the Setup menu, highlight Installation and press
T. A new set of Installation menu icons will appear.
T. A new set of Installation menu icons will appear.
2
Open the Terrestrial menu, highlight Channel Add/
Delete, and then press
Delete, and then press
T.
To add a channel to the channel memory:
Highlight the unchecked box next to the channel number you
want to add, and then press
want to add, and then press
T to check the box.
To manually add digital subchannels on a physical
channel:
channel:
Use the Channel Numbers and the Dash (
=) on the remote
control to enter the channel number (for example, 56–1).
If the channel is found, the number will be added to the list and
the box will be checked.
If the channel is not found, a message (“Not Found”) will
appear.
If the channel is found, the number will be added to the list and
the box will be checked.
If the channel is not found, a message (“Not Found”) will
appear.
To remove a channel from the channel memory:
Highlight the checked box next to the channel number you
want to remove, and then press
want to remove, and then press
T to uncheck the box.
To save your new settings:
Highlight Done and press
T.
Note: A video preview of the currently highlighted channel is
provided to assist you in adding/deleting channels.
provided to assist you in adding/deleting channels.
ANT/CABLE Cable
Scanning channels, please wait ...
Number of Channels Found - 52
Scanning Analog Channels
Found Channel - 55
Cancel
5%
(continued)
32_37CV510U_EN.book Page 29 Friday, February 22, 2008 5:40 PM