Mitsubishi wd-52527 Manuel Du Propriétaire
23
Chapter 2. Connecting
Additional connection cables are
not provided with the TV. They are
available at most electronic stores.
available at most electronic stores.
IMPORTANT
Connecting a Wall Outlet Cable or Cable Box
Wall Outlet Cable
(can be used with a CableCARD™)
Figure 1
Figure 1
It is very important to connect the incoming cable for
your primary viewing source to ANT-1, especially for
your primary viewing source to ANT-1, especially for
CableCARD™ use.
1. Connect the primary incoming coaxial lead cable to
ANT-1 MAIN on the TV back panel.
2. For an optional secondary antenna source, connect an
antenna (or cable) to ANT-2 AUX.
3. If you have subscribed to a CableCARD™ service, the
CableCARD can now be inserted into the CableCARD
SLOT. Using a Phillips screwdriver, remove the
CableCARD cover screws. Insert the CableCARD,
then replace the cover and screws. Additional
CableCARD information is on page 20.
SLOT. Using a Phillips screwdriver, remove the
CableCARD cover screws. Insert the CableCARD,
then replace the cover and screws. Additional
CableCARD information is on page 20.
Figure 1. Wall Outlet Cable
Figure 2. Connecting a Cable Box
$BCMF$"3%
5.
4-05
DPWFSSFNPWFE
DIGITAL
AUDIO
OUTPUT
CableCARD™
USE WITH
ANT 1 CARD TOP
57CBDLQBOFMTFDUJPO
1SJNBSZ
8BMM0VUMFU
$BCMF
8BMM0VUMFU
$BCMF
0QUJPOBM4FDPOEBSZ
"OUFOOBPS$BCMF
"OUFOOBPS$BCMF
DTV/CABLE/
VHF/UHF
USE WITH
CableCARD
TM
ANT 1 / MAIN
ANT 2 / AUX
Standard Cable Box
(analog cable box, other than an HDTV cable box,
compatible with PIP/POP)
Figure 2
3 coaxial cables and one two-way RF splitter are required.
compatible with PIP/POP)
Figure 2
3 coaxial cables and one two-way RF splitter are required.
These are not included with the TV.
Note: See page 29 to connect an HDTV cable box.
1. Connect the incoming cable to IN on an RF splitter.
2. Connect one coaxial cable from OUT on the RF
splitter to ANT-1 MAIN on the TV back panel.
3. Connect one coaxial cable from OUT on the RF
splitter to IN on the analog cable box.
4. Connect one coaxial cable from OUT on the cable
box to ANT-2 AUX on the TV back panel.
5. After the cable box is connected to ANT-2 AUX
as shown, open NetCommand and go to the RF
Connection for Cable screen and do the following:
Connection for Cable screen and do the following:
a. Check the RF check box.
b. For antenna, select ANT-2.
c. For Channel, select the channel to which the
b. For antenna, select ANT-2.
c. For Channel, select the channel to which the
TV must be tuned for your cable box. The
default channel is 3.
When this setup is complete, you can use the TV remote
control to change channels on the cable box.
control to change channels on the cable box.
Note: To use a cable box connected to ANT-2
as shown above, you must make the noted
NetCommand changes. The changes are
required to change the NetCommand cable-box
default connection (Component-1) to the actual
connection (ANT-2).
as shown above, you must make the noted
NetCommand changes. The changes are
required to change the NetCommand cable-box
default connection (Component-1) to the actual
connection (ANT-2).
DTV/C BLE/
VHF/UHF
ANT 1 / MAIN
ANT 2 / A
O
*ODPNJOH
$BCMF
*/
065
065
5808
"
:41-*55&3
$BCMF#PY
CBDLQBOFMTFDUJPO
*/
065
57CBDLQBOFMTFDUJPO
USE WITH
CableCARD
TM
ANT 1 / MAIN
ANT 2 / AUX
RF splitter