Mitsubishi wd-52527 Manuel Du Propriétaire
26
Chapter 2. Connecting
Connecting a VCR to Antenna or Wall Outlet Cable
Connecting VCR Video and Audio to the TV
Connecting VCR Video and Audio to the TV
Connecting VCR to an Antenna or Wall
Outlet Cable and Connecting VCR
Outlet Cable and Connecting VCR
Video and Audio to the TV
Figure 5
A two-way RF splitter, 3 coaxial cables, right and left audio
cables and an S-Video or Video cables are required. These are
not included with the TV.
not included with the TV.
1. Connect the incoming cable or Antenna to IN on the
RF splitter.
2. Connect one coaxial cable from OUT on the RF splitter
to ANTENNA IN on the VCR back panel.
3. Connect one coaxial cable from OUT on the RF splitter
to ANT-1 MAIN on the TV back panel.
4. To use the TV speakers with the VCR, connect a set of
audio cables from AUDIO OUT on the VCR back panel
to INPUT-1 AUDIO-LEFT (MONO) and AUDIO-RIGHT
on the TV back panel. The red cable connects to the
R (right) channel and the white cable connects to the
L (left) channel. If your VCR is mono (non-stereo),
connect only the white (left) cable.
Note: NetCommand® will assume your VCR is connected to inputs as shown on this page. If you use any
other inputs for your VCR or add a second VCR, this change must match in the NetCommand system. See Edit
NetCommand... in Chapter 3 for more information.
other inputs for your VCR or add a second VCR, this change must match in the NetCommand system. See Edit
NetCommand... in Chapter 3 for more information.
Figure 5. Connecting a VCR to an Antenna or Wall Outlet Cable
5. Connect either an S-Video or Video cable from VIDEO
OUT on the VCR back panel to INPUT-1 VIDEO on the
TV back panel. Only one type of video cable should
be connected. S-Video is recommended, if available.
6. For NetCommand® controlled recordings, connect a
set of audio cables from AUDIO IN on the VCR back
panel to RECORD OUTPUT AUDIO-LEFT (MONO)
and AUDIO-RIGHT on the TV back panel. The red
cable connects to the R (right) channel and the white
cable connects to the L (left) channel.
7. Complete the NetCommand controlled recordings
connections by connecting a Video cable from VIDEO
IN on the VCR back panel to RECORD OUTPUT
VIDEO on the TV back panel.
57CBDLQBOFM
"UUBDIPOMZPOFDBCMFUZQF
47JEFPSFDPNNFOEFEJGBWBJMBCMF
)46
7$3CBDLQBOFM
*GZPVS7$3IBTBWJEFPDIBOOFM
PS3'0/0''TXJUDI TFUJUUP0''
PS3'0/0''TXJUDI TFUJUUP0''
*/
065
065
5808
"
:41-*55&3
*ODPNJOH$BCMF
COMPONENT
YPbPr (480i/480p/720p/1080i)
INPUT
1
2
S-VIDEO
VIDEO
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
DIGITAL
AUDIO
OUTPUT
CableCARD™
USE WITH
ANT 1 CARD TOP
1
2
Y
Pb
Pr
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
OUTPUT
AUDIO
OUTPUT
RECORD
OUTPUT
DVI
Analog Audio
1
2
VIDEO
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
SERVICE
PORT
MONITORLINK™/HDMI
VIDEO 480i/480p/720p/1080i
AUDIO PCM LINEAR
1
1
2
IEEE 1394
INPUT/
OUTPUT
Net Command
IR EMITTER
¥
(-JOL
¥
INPUT
3
DTV/CABLE/
VHF/UHF
USE WITH
CableCARD
TM
ANT 1 / MAIN
ANT 2 / AUX