Siemens sl785 Mode D'Emploi
59
Questions and answers
Gigaset SL785 / USA en / A31008-M2009-R301-4-6019 / appendix.fm / 14.02.2011
V
e
rsion 4, 16.0
9
.2005
Questions and answers
If you have any questions about using your
phone, visit us any time at
www.gigaset.com/service.
The table below contains a list of common
problems and possible solutions.
phone, visit us any time at
www.gigaset.com/service.
The table below contains a list of common
problems and possible solutions.
Registration or connection problems with a
Bluetooth headset.
Bluetooth headset.
¥
Reset the Bluetooth headset (see the user
guide for your headset).
guide for your headset).
¥
Delete registration data from the handset
when deregistering the device (
when deregistering the device (
¥
Repeat the registration process (
The display is blank.
1. The handset is not switched on.
¥
Press and hold the End Call key
a
.
2. The battery is dead.
"
No Base
" flashes in the display.
1. The handset is outside the range of the base
station.
¥
Move the handset closer to the base sta-
tion.
tion.
The base station's range is reduced because
Eco mode is activated.
Eco mode is activated.
¥
Deactivate Eco mode (
page 41), or
reduce the distance between the handset
and the base station.
and the base station.
2. The base station is not turned on.
"
Please register handset
" flashes in the
display.
Handset has not been registered with the base
station or has been deregistered.
station or has been deregistered.
¥
Register the handset (
Handset does not ring.
The ringer is deactivated.
¥
Activate the ringer (
You cannot hear a ringer/dial tone from the
landline network.
landline network.
The phone cord supplied has not been used or
has been replaced by a new cord with the wrong
pin connections.
has been replaced by a new cord with the wrong
pin connections.
¥
Always use the phone cord supplied, or
ensure that the pin connections are correct
when purchasing from a retailer (
ensure that the pin connections are correct
when purchasing from a retailer (
Error tone sounds after system PIN prompt.
You have entered the wrong system PIN.
¥
Reset the system PIN to 0000 (
Forgotten the system PIN.
¥
Reset the system PIN to 0000 (
The other party cannot hear you.
You have pressed the
§Mute§
Display key.
The handset is muted.
¥
Activate the microphone again (
The number of the caller is not displayed
despite CID.
despite CID.
Caller ID is not enabled.
¥
The caller should ask the network provider to
release Caller ID (CID).
release Caller ID (CID).
You hear an error tone when keying an input (a
descending tone sequence).
descending tone sequence).
Action has failed/invalid input.
¥
Repeat the operation. Watch the display and
refer to the user guide, if necessary.
refer to the user guide, if necessary.
You cannot listen to messages on the network
mailbox.
mailbox.
Your PABX is set for pulse dialing.
¥
Set your PABX to touch-tone dialing.
No time is specified for a message in the Call lists.
Date and time have not been set.
¥
Set the date/time (
The answering machine announces "PIN is
incorrect" during remote operation.
incorrect" during remote operation.
1. You have entered the wrong system PIN.
¥
Enter the system PIN again.
2. The system PIN is still set to 0000.
¥
Change the system PIN (
The answering machine is not recording any
messages/has switched to answer only.
messages/has switched to answer only.
Its memory is full.
¥
Delete old messages.
¥
Play back new messages and delete.