Pantech crossover Guide De Spécification
100
Appendix
higher of the two ratings.
Hearing devices may also be rated. Your hearing device
manufacturer or hearing health professional may help you
find this rating. Higher ratings mean that the hearing device is
relatively immune to interference noise. The hearing aid and
wireless phone rating values are then added together. A sum
of 5 is considered acceptable for normal use. A sum of 6 is
considered for best use.
manufacturer or hearing health professional may help you
find this rating. Higher ratings mean that the hearing device is
relatively immune to interference noise. The hearing aid and
wireless phone rating values are then added together. A sum
of 5 is considered acceptable for normal use. A sum of 6 is
considered for best use.
In the above example, if a hearing aid meets the M2 level rating
and the wireless phone meets the M3 level rating, the sum of
the two values equals M5. This is synonymous for T ratings.
This should provide the hearing aid user with “normal usage”
while using their hearing aid with the particular wireless phone.
“Normal usage” in this context is defined as a signal quality that
is acceptable for normal operation.
and the wireless phone meets the M3 level rating, the sum of
the two values equals M5. This is synonymous for T ratings.
This should provide the hearing aid user with “normal usage”
while using their hearing aid with the particular wireless phone.
“Normal usage” in this context is defined as a signal quality that
is acceptable for normal operation.
The M mark is intended to be synonymous with the U mark.
The T mark is intended to be synonymous with the UT mark.
The M and T marks are recommended by the Alliance for
Telecommunications Industries Solutions (ATIS). The U and
UT marks are referenced in Section 20.19 of the FCC Rules. The
HAC rating and measurement procedure are described in the
American National Standards Institute (ANSI) C63.19 standard.
The T mark is intended to be synonymous with the UT mark.
The M and T marks are recommended by the Alliance for
Telecommunications Industries Solutions (ATIS). The U and
UT marks are referenced in Section 20.19 of the FCC Rules. The
HAC rating and measurement procedure are described in the
American National Standards Institute (ANSI) C63.19 standard.
To ensure that the Hearing Aid Compatibility rating for
your phone is maintained, secondary transmitters such as
Bluetooth and WLAN components must be disabled during a
call. See page 66 for instructions to disable these components.
your phone is maintained, secondary transmitters such as
Bluetooth and WLAN components must be disabled during a
call. See page 66 for instructions to disable these components.
FCC Regulatory Compliance
FCC Regulatory Compliance
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must
accept any interference received, including interference
that may cause undesired operation. Your mobile device is
a low power radio transmitter and receiver. When it is ON, it
receives and also sends out radio frequency (RF) signals. In
August 1996, the Federal Communications Commission (FCC)
adopted RF exposure guidelines with safety levels for mobile
devices. Those guidelines are consistent with safety standards
previously set by both U.S. and international standards
bodies: American National Standard Institute (ANSI),
National Council of Radiation Protection and Measurements
(NCRP), and International Commission on Non-Ionizing
Radiation Protection (ICNRP). Those standards were based
on comprehensive and periodic evaluations of the relevant
scientific literature. The design of your phone complies with
the FCC guidelines and applicable.
is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must
accept any interference received, including interference
that may cause undesired operation. Your mobile device is
a low power radio transmitter and receiver. When it is ON, it
receives and also sends out radio frequency (RF) signals. In
August 1996, the Federal Communications Commission (FCC)
adopted RF exposure guidelines with safety levels for mobile
devices. Those guidelines are consistent with safety standards
previously set by both U.S. and international standards
bodies: American National Standard Institute (ANSI),
National Council of Radiation Protection and Measurements
(NCRP), and International Commission on Non-Ionizing
Radiation Protection (ICNRP). Those standards were based
on comprehensive and periodic evaluations of the relevant
scientific literature. The design of your phone complies with
the FCC guidelines and applicable.
Statement according to FCC part 15.105
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by