Shure scl3 Mode D'Emploi
SCL3
Sound Isolating Earphones
With a sleek, low profile design,
the SCL3 combines WideBand
MicroDriver technology and
incredible sound isolation for
detailed highs
and enhanced
bass across an
extended frequency
soundstage.
Originally designed
for the demanding
audio specifications
of professional
musicians, the SCL3
is an ideal choice for any
home or portable audio
device.
�
INSERTING THE EARPHONES
If the earphone seems to be lacking in low frequency response (bass), check
the tightness of the seal between the earphone and your ear, or try one of the
other sleeve options.
the tightness of the seal between the earphone and your ear, or try one of the
other sleeve options.
Warning: Do not push the earphone sleeve beyond the ear canal opening.
WEARING THE EARPHONES
Three popular methods for wearing the earphones are illustrated below.
CHOOSING AN EARPHONE SLEEVE
Your earphones come with a selection of sleeves. Make sure the sleeve you
use is easy to insert into your ear, fits comfortably, and is easy to remove from
your ear.
use is easy to insert into your ear, fits comfortably, and is easy to remove from
your ear.
CLEANING THE EARPHONE NOZZLE
If the nozzle of your earphone is blocked, clean the nozzle using the supplied
wax removal loop.
wax removal loop.
SHURE Incorporated http://www.shure.com
United States, Canada, Latin America, Caribbean:
5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.
Phone: 847-600-2000 U.S. Fax: 847-600-1212 Int’l Fax: 847-600-6446
Europe, Middle East, Africa:
Shure Europe GmbH, Phone: 49-7131-72140 Fax: 49-7131-721414
Asia, Pacific:
Shure Asia Limited, Phone: 852-2893-4290 Fax: 852-2893-4055
Triple-Flange Sleeves (Optional Accessory)
If desired, the sleeve nozzle may be shortened. Use sharp
scissors to carefully trim the nozzle to the desired length.
If desired, the sleeve nozzle may be shortened. Use sharp
scissors to carefully trim the nozzle to the desired length.
Yellow and Soft Black Foam Sleeves
When using the foam sleeves, compress the sleeve between
your fingers before inserting it into the ear canal. Hold the
earphone in place for about ten seconds while the foam
expands and creates a tight seal. Black foams come in
small, medium and large sizes.
When using the foam sleeves, compress the sleeve between
your fingers before inserting it into the ear canal. Hold the
earphone in place for about ten seconds while the foam
expands and creates a tight seal. Black foams come in
small, medium and large sizes.
Soft Flex Sleeves
In small, medium, and large sizes. Made from pliable
rubber.
In small, medium, and large sizes. Made from pliable
rubber.
Nozzle
Wax Removal Loop
Tighten the cable and take up slack by raising the cable sleeve .
When cleaning, do not force any object through the earphone nozzle! This will
damage the earphone sound filter.
damage the earphone sound filter.
©2007, Shure Incorporated
27EN3249 (Rev. 1)
27EN3249 (Rev. 1)
Printed in U.S.A.
Over the ear
in back
in back
Over the ear
in front
in front
Straight down
left ear
right ear
Note:
slide sleeve over earphone nozzle barb for a secure grip.
To change earphone sleeve, twist and pull sleeve to remove it from the nozzle. Push new sleeve
onto nozzle until you feel it slide completely over barb. If any part of the nozzle is exposed,
sleeve is not properly installed. Replace sleeves if they do not grip the nozzle tightly.
onto nozzle until you feel it slide completely over barb. If any part of the nozzle is exposed,
sleeve is not properly installed. Replace sleeves if they do not grip the nozzle tightly.
Nozzle Barb
Sleeve
Sleeve Over Barb
Warning: The wax removal loop is only to be used to clean
earphones. Any other use, such as using the tool to clean
ears, could result in injury.
earphones. Any other use, such as using the tool to clean
ears, could result in injury.