Runco CL-810 Manuel D’Utilisation
74
Runco CL-810 Series Owner’s Operating Manual
P
RELI
M
INARY
Brightness and Contrast:
Cinema Standards Measurement System (CSMS)
Specifications
-
Specifications
-
Brightness*: 14.5 to 21.6 foot-Lamberts (fL)
-
Contrast Ratio*: 200:1 to 220:1
*Variable depending on RVR setting
These measurements are taken from the projector in a controlled,
home theater environment. All measurements are made to
ANSI/NAPM IT7.228-1997 specifications using the Photo Research
PR-650 SpectraColorimeter and Minolta LS-100 Luminance Meter,
Video Essentials test DVD and a 1.3 gain, 72-inch wide screen. The
projector is calibrated to a color temperature of 6,500K and has a
minimum of 150 hours of usage.
The foot-Lambert (fL) is the unit of measurement used in commercial
movie theaters to express image brightness at the screen surface. The
Society of Motion Picture and Television Engineers (SMPTE) specifies
16 fL as the target image brightness for film-based projectors using an
open gate (without film in the projector). More importantly, today
SMPTE specifies 12 fL as the target image brightness in Digital
Cinema theaters. The foot-Lambert measurement is dependent on
screen size, screen gain and projector light output.
home theater environment. All measurements are made to
ANSI/NAPM IT7.228-1997 specifications using the Photo Research
PR-650 SpectraColorimeter and Minolta LS-100 Luminance Meter,
Video Essentials test DVD and a 1.3 gain, 72-inch wide screen. The
projector is calibrated to a color temperature of 6,500K and has a
minimum of 150 hours of usage.
The foot-Lambert (fL) is the unit of measurement used in commercial
movie theaters to express image brightness at the screen surface. The
Society of Motion Picture and Television Engineers (SMPTE) specifies
16 fL as the target image brightness for film-based projectors using an
open gate (without film in the projector). More importantly, today
SMPTE specifies 12 fL as the target image brightness in Digital
Cinema theaters. The foot-Lambert measurement is dependent on
screen size, screen gain and projector light output.
Home Theater Calibration Specifications
-
-
Light Output: 442 to 587 ANSI Lumens
-
Contrast Ratio*: 200:1 to 220:1
These specifications are obtained by calibrating the projector as
described above for CSMS measurements.
described above for CSMS measurements.
Industry-Standard Specifications
-
-
Light Output: 1250 ANSI Lumens
-
Contrast Ratio: 1500:1 to 3100:1
These are typical projector brightness and contrast specifications
found in most companies’ sales literature. Runco includes these
measurements in its literature to allow for direct comparison with other
manufacturers’ projectors. These measurements are typically taken at
9,000K to 13,000K to get expected performance data when the
projector is used in professional, commercial and industrial displays.
found in most companies’ sales literature. Runco includes these
measurements in its literature to allow for direct comparison with other
manufacturers’ projectors. These measurements are typically taken at
9,000K to 13,000K to get expected performance data when the
projector is used in professional, commercial and industrial displays.
Lamp:
250 Watts
Estimated Lamp Life:
2000 hours
Video Inputs:
(1) Composite Video, (1) S-Video, (1) RGB/Component Video
(BNC connectors), (1) RCA Component Video, (1) HDMI
(BNC connectors), (1) RCA Component Video, (1) HDMI
Control Options:
-
Discrete IR remote
-
Serial commands via RS-232
RS-232 Communication
Parameters:
Parameters:
9600, 38400 or 115200 bps, no parity, 8 data bits, 1 stop bit,
no flow control
no flow control
12V Output:
Max. 0.25 Amps, active when Cinema or Virtual Cinema
Aspect Ratio is selected (CL-810/CineWide with AutoScope
only) or when projector is turned on; Tip = +12V;
Sleeve = Ground
Aspect Ratio is selected (CL-810/CineWide with AutoScope
only) or when projector is turned on; Tip = +12V;
Sleeve = Ground
Power Requirements:
100 to 240 VAC (auto-sensing), 50/60 Hz, 310 Watts
Operating Environment:
41°F to 95°F (5°C to 35°C), 20% to 80% humidity
(non-condensing)
Dimensions:
CL-810: See Figure 7-1
CL-810 Ultra: See Figure 7-2
CL-810 Ultra: See Figure 7-2
Table 7-1. CL-810 Specifications (continued)