Fujifilm S2-Pro Manuel Du Propriétaire

115

114

—

i Switch the camera off and replace the lithium

batteries. Then switch the camera back on
and try again.
If this does not resolve the problem, set the

focusing mode to “M”, release the shutter and
briefly switch the camera off.

i The lithium batteries are low on

charge or the camera mechanism
has stopped due to cold and
cannot take pictures.

(blinking)

i Switch the camera off, close the slot cover,

switch the camera back on and try again.

i Switch the camera off and replace the AA-

size batteries or load new AA-size batteries.
Then switch the camera back on and try
again.

—

i Release shutter again. If the warning

indication remains, or this warning appears
frequently, contact you FUJIFILM dealer.

i Malfunction detected.

(blinking)

(blinking)

i The slot cover was opened during

card operation.

i The AA-size batteries are low on

charge or flat.

i No AA-size batteries are loaded.

(lit)

(lit)

(blinking)

(blinking)

eThe table below lists the warning messages displayed on the

top display panel or in the viewfinder.

i CPU Nikkor lens other than G-type

is not set to its minimum aperture.

i Attached flash is not set at TTL

Auto Flash in “P” mode.

i Set lens to minimum aperture.

i Set the external flash mode to TTL, or set the

camera’s exposure mode to “S”, “A” or “M”.

(blinking)

(blinking)

i Lithium Batteries are low on charge. i Have new ones ready.

—

i Lithium Batteries have no remaining

charge.

i Turn the power off and replace lithium

batteries with new ones.

i Attach CPU lens (except IX-Nikkor). With a

non-CPU lens, set the exposure mode to “M”
and set the aperture with lens’ aperture ring.

—

i Non-CPU lens is attached or lens is

not attached.

(blinking)

(blinking)

i Focus manually.

i Autofocus is not possible.

—

(blinking)

i In  “P” mode, use ND filtre (If the warning

indication remains after performing above
remedies in “S” or “A” mode, use ND filtre as
well).

i In “S” mode, select faster shutter speed.
i In “A” mode, select smaller aperture (larger f-

number).

i Overexposure warning (subject is

too bright).

(lit)

(lit)

i In  “P” mode, use flash (If the warning

indication remains after performing above
remedies in “S” or “A” mode, use flash as
well).

i In “S” mode, select slower shutter speed.
i In “A” mode, select larger aperture (smaller f-

number).

i Underexposure warning (subject is

too dark.).

(lit)

(lit)

i When the subject is too bright, use ND filtre

and when the subject is too dark, use flash
too the electronic analog exposure display
remains blinking when the flash is used.

i Subject brightness is beyond

camera’s exposure range.

—

Electronic

analog

exposure

display

(blinking)

i Release the shutter as it is to take a flash

picture (Shutter speed automatically shifts to
1/125 sec.).

i Shutter speed faster than sync

speed is selected in “S” or “M”
mode.

Shutter speed 

indication

(blinking)

(lit)

i Cancel the “™”  or select “M” mode.

i Shutter speed is set to “™” in

“S” mode.

(blinking)

i Shoot again after confirming focus distance,

aperture or flash shooting distance range.

i Flash has fired at full output and

underexposure may have occurred.

—

(blinking)

In certain cases, due to static electricity or poorly loaded batteries, the FinePix S2 Pro
microcomputer may turn the camera off, even with fresh, properly installed batteries. For the same
reason, the operation of camera may not advance properly during either “USB mode” or “IEEE1394
mode”. In each of these cases, to resume operation, simply turn the power off, then turn it on
again. Or, remove and reinstall the batteries.