Cool-Icam cic-101 Manuel D’Utilisation

19

I  cannot  activate  my  Stylus  1000  by 

pressing the Mode Button.

I  receive  an  error  message  when  I  am 

installing the Digital Camera Manager. 

Plug-in  le  and  “STV0680  Camera 

Snapshots”/”WWL  Mac”  folder  is  not 

found in the Hard disk after I have installed 

the driver.

All the images I have taken do not appear 

on the Stylus 1000. 

I  receive  a  message  no  image  to 

download.

I  cannot  run  the  STV0680  Capture”/

”WWL Mac Import.

I hear a low “beep” when trying to take an 

image.

I  cannot  access  any  PhotoFantasy’s 

templates.

Shut  down  all  other  applications  and  attempt  to 

reinstall the driver, or download the updated driver from 

www.coolicam.com and install the updated driver.

Install  the  software,  restart  your  Mac,  and  nally, 

connect the Stylus 1000 to the Mac via the USB port, 

then the plug-in le and folder will appear in the Hard 

disk.

Upload  all  images  to  your  Mac  as  soon  as  possible. 

(please  refer  to  Battery  Guidance  section  in  User’s 

Manual.)

If  you  need  to  change  batteries,  and  retain  the 

images  in  your  Stylus  1000’s  memory,  ensure  you 

are  connected  to  a  Mac  which  is  turned  on  via  the 

USB cable, which will then draw power from the Mac 

whilst you insert fresh batteries or make sure there is 

sufcient power on the backup battery.

Upload  saved  images  immediately,  then  replace 

battery.

If  you  have  any  other  camera  installed  on  your 

computer, remove the camera and it’s driver completely 

from your system to avoid conict with another camera 

or capture device.

Put “Digital Camera” CD in CD ROM drive.

Take your images in better light condition.

Upload all images to your Mac and replace batteries.

Digital Camera Manager does not load.

You have lost power to your Stylus 1000 by either:

The  installer  for  the  Digital  Camera 

Manager  requires  the  Stylus  1000  be 

connected  to  the  PC  (via  the  USB)  after 

the  software  has  been  installed  &  the  PC 

restarted.

Insufcient battery power.

Battery power is too low to continue taking 

images.

Connection failure.

Removing  the  battery  without  being 

connected to your Mac (turned on) via the 

USB cable.

Insufcient light.

No CD in CD-ROM drive.

Insufcient  battery  power  or  batteries  is 

missing.

LCD display is ashing.

Conict with another camera driver capture 

device.

Check all cables connections are secured.

 

We strongly recommend that you do not use rechargeable batteries as this will affect 
the performance of your Stylus 1000 and Flash Bar.

• Batteries should be replaced by an adult.

• Non-rechargeable batteries are not to be recharged.

• Rechargeable batteries are to be removed from the camera before being charged (if removable).

• Rechargeable batteries are only to be charged under adult supervision (if removable).

• Different types of batteries or new and used batteries are not to be mixed.

• Only batteries of the same or equivalent type as recommended are to be used.

• Batteries are to be inserted with the correct polarity.

• Exhausted batteries are to be removed from the camera.

• The supply terminals are not to be short-circuited.

• Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries.

• Do not dispose the batteries in re.

• Batteries are to be removed from the camera when not in use.

• Do not use rechargeable batteries.

  These instructions should be retained for future reference.