Haier ad88nahbea Manuel D’Utilisation
Change of fan speed
In COOLING mode, the air sending is set at AUTO,
when the indoor temperature is near the set temperature,
the fan speed will lower automatically.In HEATING
mode, when room temperature reaches the
set temperature, the compressor will stop
running, and the fan will change to LOW
FAN or stop.
In COOLING mode, the air sending is set at AUTO,
when the indoor temperature is near the set temperature,
the fan speed will lower automatically.In HEATING
mode, when room temperature reaches the
set temperature, the compressor will stop
running, and the fan will change to LOW
FAN or stop.
In DEHUMIDIFYING mode,
the fan speed will change automatically.
3-minute protection function
If start the unit immediately only
after it is turned off, the compressor
will start
after 3
minutes have
elapsed to protect
the compressor.
Operation of air conditioner
When the ambient
humidity is too high,
in COOLING or
DEHUMIDIFYING
mode, there may be water
dropped in the air outlet.
humidity is too high,
in COOLING or
DEHUMIDIFYING
mode, there may be water
dropped in the air outlet.
Anti-cold air blowing out
During Heating operation, after starting the
unit, the indoor fan motor
will not rotate immediately
to prevent
cold air from
blowing out.
During Heating operation, after starting the
unit, the indoor fan motor
will not rotate immediately
to prevent
cold air from
blowing out.
Defrosting function
During Heating operation, when frost formed on the
heat exchanger of outdoor unit, the air conditioner
will defrost automatically for several minutes. During
defrosting, both the fan of indoor and
outdoor unit do not run. After
finishing defrosting, the air
conditioner will automatically
resume operation.
heat exchanger of outdoor unit, the air conditioner
will defrost automatically for several minutes. During
defrosting, both the fan of indoor and
outdoor unit do not run. After
finishing defrosting, the air
conditioner will automatically
resume operation.
Hint
When the air conditioner
is in Heating mode, it
a b s o r b s h e a t f r o m
outside and release to
indoors. So the outdoor
temperature may affect
the Heating effect.
is in Heating mode, it
a b s o r b s h e a t f r o m
outside and release to
indoors. So the outdoor
temperature may affect
the Heating effect.
Power failure resume function (please set and use this function according to actual
condition)
After setting power failure resume function, if there is a sudden power failure during
unit operation, when power on for again, the unit will resume the previous state.
unit operation, when power on for again, the unit will resume the previous state.
Setting method
: when the wire controller is in ON state (except for TIMER and FAN
mode), press the SLEEP button for 10 times in 5 seconds, after the buzzer sounds 4
times, the unit will change to POWER FAILURE RESUME function.
Cancellation method: press the SLEEP button 10 times in 5 seconds, after the buzzer
2 times, the POWER FAILURE RESUME function is cancelled.
times, the unit will change to POWER FAILURE RESUME function.
Cancellation method: press the SLEEP button 10 times in 5 seconds, after the buzzer
2 times, the POWER FAILURE RESUME function is cancelled.
Note
: After the unit is set POWER FAILURE RESUME function, if there is a sudden power failure
in using, during this period of time if there is no need to use the unit for a long time, please cut off
power to prevent the air conditioner from automatically resuming to the previous setting if powerfailure
resumes, or press the ON/OFF button to turn off the unit after power failure resumes.
Operation points
1
?
MODE
FAN
SWING
TEMP
CLOCK
TIMER
SET
SLEEP
FILTER RESET
RESET
ON/OFF
MODE
FAN
SWING
TEMP
CLOCK
TIMER
SET
SLEEP
FILTER RESET
RESET
ON/OFF
MODE
FAN
SWING
TEMP
CLOCK
TIMER
SET
SLEEP
FILTER RESET
RESET
ON/OFF
MODE
FAN
SWING
TEMP
CLOCK
TIMER
SET
SLEEP
FILTER RESET
RESET
ON/OFF