Freestyle fs84950 Manuel D’Utilisation

FS 1064 Gromatide AG7027-INST-R01

2741

AG7027

27/01/2010

•  Tide data for 75 beaches worldwide

•  180 minute offset

•  Displays present and future tide data

•  9 programmable favorite locations

•  Optional big time with shark fin

 animation

•  100 meters H20

This Freestyle product features unique

Hydro Pushers®: these pushers can be

pressed under water to a dynamic water

pressure (not water depth) of 3 ATM.

S1: Start Button

S2: Stop/Reset Button

S3: Mode Button

S4: Set Button

S5: Light Button

The watch has six display modes: NORMAL

TIME, TIDE, CHRONO, TIMER, HEAT TIMER

and ALARM.

To change from one display mode to

another, press S3 button once.

NOTE: In any setting mode, if there is no

manipulation for about 120 seconds, the

watch will automatically exit the setting

procedure.

1.  Press S3 button to select NORMAL TIME

mode.

2.  Press and hold S4 button for two sec-

onds until the “SET” message appears

and the Time Zone blinks on the display.

3.  Press S1 button or S2 button to toggle

between Time Zone 1 and Time Zone 2.

4.  Press S3 button once, the Hour digits

(including AM / PM for 12-hour format)

will blink.

5.  Press S1 button to increase the digits by

one unit, or press S2 button to decrease

the digits by one unit. Holding down

either button will speed up the process.

6.  Press S3 button once, the Minute digits

will blink.

7.  Press S1 button or S2 button to set the

Minute digits.

8.  Press S3 button once, the Second digits

 will blink.

9.  Press either S1 button or S2 button to

 set the Second digits to zero.

10.Press S3 button once, the Month digits

will blink.

11.Press S1 button or S2 button to set the

Month digits.

12.Press S3 button once, the Date digits

will blink.

13.Press S1 button or S2 button to set the

Date digits.

14.Press S3 button once, the Year digits

will blink.

15.Press S1 button or S2 button to set the

Year digits.

16.Press S3 button once, the Time Format

will blink.

17.Press S1 button or S2 button to toggle

between 12-hour and 24-hour Time

Format.

18.Press S3 button once, the Date Format

will blink.

19.Press S1 button or S2 button to cycle

among MM-DD-YY (month-date-year),

DD-MM-YY (date-month-year) and YY-

MM-DD (year-month-date) to set the

Date Format.

20.Press S3 button once, the Day (of the

week) Language will blink.

21.Press S1 button or S2 button to cycle

among English, French, Portuguese and

Spanish to set the Day Language.

22.Press S3 button once, the Hourly Chime

status will blink.

23.Press S1 button or S2 button to toggle

between ON and OFF of Hourly Chime.

24.Press S3 button once, the Button Beep

status will blink.

25.Press S1 button or S2 button to toggle

between ON and OFF of Button Beep.

26.Press S3 button once, the Big Time Op-

tion status will blink.

27.Press S1 button or S2 button to toggle

between ON and OFF of Big Time Op-

tion.

28.Press S3 button once, the Tide Height

unit will blink.

29.Press S1 button or S2 button totoggle

between feet and meters for Tide Height

unit.

30.After finished making all the settings,

press S4 button to confirm the settings.

NOTE: The date is displayed in the current

Date Format, but the setting sequence

shall always be month, date, and then year,

regardless of the Date Format chosen.

NOTE: The available days of the month

shall be determined by the month setting.

If February is set, the available days of the

month shall be 1 to 29. If February 29 is set

for a year that is not a leap year, the date

shall be corrected to February 28 upon exit

from the setting procedure.

NOTE: For Big Time Option, if OFF is

selected, only date/time and tide/time

formats will be available in NORMAL TIME

mode; if ON is selected, the Big Time

display format shall also be available in

NORMAL TIME mode.

NOTE: The Time Format and Date Format

settings apply only to the selected Time

Zone; while the settings of Day Language,

Hourly Chime, Button Beep, Big Time

Option and Tide Height unit apply to both

Time Zones.

There are three display formats in each

Time Zone in NORMAL TIME mode: date/

time, tide/time and big time.

To change from one Time Zone to another,

press S2 button once.

To change from one display format to

another, press S1 button once.

In date/time display format,

the primary time day and date are shown

in the top of the display; the time in hours,

minutes and seconds is shown in the bot-

tom of the display. The data is shown in the

Date and Time Formats of the displayed

Time Zone, which are set in this mode

along with the date and time.

If there is previous and upcoming tide data,

the left-hand part of the display shows

the tide status for the currently selected

tide location. Otherwise, no graphic is

displayed.

In tide/time display format,

the display is identical to the date/time

format except that the next tide (high or

low) for the currently selected tide location,

the time of the next tide, and its height are

shown in place of the day and the date. The

tide time is shown in the same format as

the primary time. The Tide Height is shown

in the current Tide Height unit selected.

If no previous or upcoming tide data is

available, this format shall be unavailable

and the format shall revert to date/time.

In big time display format,

only the hours and minutes of the primary

time are shown, no AM/PM indication.

A shark fin animation shall occur once per

minutes. For even minutes, the fin shall

move from left to right one dot column at

a time, and for odd minutes, the fin shall

move from right to left.

The big time display format is included only

if the Big Time Option is on.

NOTE: The current tide level and direction

(rising or falling) shall be presented by a

tide status graphic, which is represented by

an arrow head two dots high and three dots

wide. The steps shall appear as follows:

In displays 1 through 10, the tide is rising;

while in display s 11 through 20, the tide

is falling. When the time of day advances

to the minute after the time of high tide,

display 11 is shown; when the time of day

advances to the minute after the time of

low tide, the sequence repeats beginning

with display 1.

For displaying tide information of current

time and location,

1. Press S3 button to select TIDE mode.

 The favorite number and the name of

 current tide location will appear.

2. After two seconds, the next upcoming

tide (high or low), base on the primary

time, for the current tide location will

be displayed. The date will be displayed

in the top line, the next tide will be dis-

played in the middle line followed by the

time of that tide (with a superscript A/P

representing AM/PM in 12-hour format),

and the height of the next tide will be

displayed in the bottom line (including

minus sign if necessary).

3. Press S1 or S2 button to display the

 previous and next tide respectively.

4. Press and hold S1 button or S2 button

 until the “SCAN” message appears to

 initiate date scanning in the forward or

 backward direction respectively.

5. Release either button when the desired

 date is displayed.

6. After abandoning the date scanning

 procedure, while the “SCAN” message is

 still displayed, press S1 button or S2

 button to move forward or backward

 respectively the displayed date by one

 day. Press and hold the correspond-

 ing buttons to reinitiate date scanning.

NOTE: If no previous or upcoming tide data

is available, the sentence “NO TIDE DATA

FOR DATE” will be displayed.

NOTE: The date, time and tide height unit

will be displayed in the formats of the

primary time set in NORMAL TIME mode.

NOTE: If the displayed time represents DST

(daylight savings time), which means that

the time was adjusted from the stored tide

data, the DST flag will appear.

NOTE: Scanning shall stop automatically

if the last date for which there is tide data

is reached.

For setting tide location,

1.  Press S3 button to select TIDE mode.

The favorite number and the name of

current tide location will appear.

2.  Press S4 button, the “SET” message ap-

 pears and the FAV (favorite) number

blinks on the display. The default favor-