ONKYO HT-S8400 Manuel D’Utilisation

En

• “Picture Adjust” cannot be used with the NET input selector.

*1

This procedure can also be performed on the remote controller 
by using the Home menu (

*2

When a 3D video source is input, “Wide Mode” is fixed to 
“Full”.

*3

When the “Picture Mode” setting is set to anything other than 
“Custom”, this setting cannot be used.

*4

If the “Resolution” setting is set to “4K Upscaling” 
(

page 40), this setting is fixed to “Off”.

*5

Press CLR if you want to reset to the default value.

*6

If you are using the analog RGB input, this setting is not 
available.

*7

If the “Game Mode” setting is set to “On”, this setting is 
fixed to “Off”.

You can set priorities of audio output when there are both 
digital and analog inputs.

■

`

ARC:

The audio signal from your TV tuner can be sent to 
the HDMI OUT of the AV receiver.

*1

With this selection, the TV’s audio can be 
automatically selected as a priority among other 
assignments.

`

HDMI:

This can be selected when HDMI IN has been 
assigned as an input source. If both HDMI (HDMI 
IN) and digital audio inputs (COAXIAL IN or 
OPTICAL IN) have been assigned, HDMI input is 
automatically selected as a priority.

`

COAXIAL:

This can be selected when COAXIAL IN has been 
assigned as an input source. If both coaxial and 
HDMI inputs have been assigned, coaxial input is 
automatically selected as a priority.

`

OPTICAL:

This can be selected when OPTICAL IN has been 
assigned as an input source. If both optical and 
HDMI inputs have been assigned, optical input is 
automatically selected as a priority.

`

Analog:

The AV receiver always outputs analog signals.

• The setting is stored individually for each input selector.
• This setting can be made only for the input source that is 

assigned as HDMI IN, COAXIAL IN, or OPTICAL IN.

• The  “Audio Selector” settings cannot be used with the NET, 

USB and PORT (with connected component) input selectors.

*1

You can select “ARC” if you select the TV/CD input selector. 
But you cannot if you’ve selected “Off” in the “Audio 
Return Channel” setting (

page 52).

■

`

Off:

The format is detected automatically. If no digital 
input signal is present, the corresponding analog 
input is used instead.

`

PCM:

Only 2-channel PCM format input signals will be 
heard. If the input signal is not PCM, the PCM 
indicator will flash and noise may also be produced.

`

DTS:

Only DTS (but not DTS-HD) format input signals 
will be heard. If the input signal is not DTS, the DTS 
indicator will flash and there will be no sound.

When “HDMI”, “COAXIAL” or “OPTICAL” is 
selected in the “Audio Selector” setting, you can then 
specify the signal type in “Fixed Mode”.
Normally, the AV receiver detects the signal format 
automatically. However, if you experience either of the 
following issues when playing PCM or DTS material, you 
can manually set the signal format to PCM or DTS.
• If the beginnings of tracks from a PCM source are cut 

off, try setting the format to PCM.

• If noise is produced when fast forwarding or reversing a 

DTS CD, try setting the format to DTS.

• The setting is stored individually for each input selector.
• The setting will be reset to “Off” when you change the setting in 

“Audio Selector”.

■

`

Auto:

Power feeding is interrupted when your iPod/iPhone 
is fully charged.

`

On:

Power feeding continues even if your iPod/iPhone is 
fully charged.

`

Off:

Your iPod/iPhone is not charged.

You can specify how the power is fed to your iPod/iPhone 
when the AV receiver is in standby mode.

• This setting cannot be selected when:

– the UP-A1 Dock with docked iPod/iPhone is not connected to 

the AV receiver, or

– the docked iPod/iPhone model is not supported.

• When the “Charge Mode” setting is set to “On”, or to “Auto” 

with your iPod/iPhone recharging, the SLEEP indicator is dimly 
lit in standby mode. In such conditions, the power consumption 
of the AV receiver slightly increases.