ONKYO TX-NR3009 Mode D'Emploi
65
En
■
Power On Volume
`
Last, Min, 1 to 99 or Max (Absolute display)
`
Last
, –
QdB, –81dB to +18dB (Relative display)
With this preference, you can specify the volume setting
to be used each time the AV receiver is turned on.
To use the same volume level that was used when the AV
receiver was turned off, select “Last”.
The “Power On Volume” cannot be set higher than the
“Maximum Volume” setting.
to be used each time the AV receiver is turned on.
To use the same volume level that was used when the AV
receiver was turned off, select “Last”.
The “Power On Volume” cannot be set higher than the
“Maximum Volume” setting.
■
Headphone Level
`
–12dB to 0dB to +12dB
With this preference, you can specify the headphone
volume relative to the main volume. This is useful if
there’s a volume difference between your speakers and
your headphones.
volume relative to the main volume. This is useful if
there’s a volume difference between your speakers and
your headphones.
OSD Setup
■
On Screen Display
`
On
`
Off
This preference determines whether operation details are
displayed on-screen when an AV receiver function is
adjusted.
Even when “On” is selected, operation details may not be
output if the input source is connected to an HDMI IN.
displayed on-screen when an AV receiver function is
adjusted.
Even when “On” is selected, operation details may not be
output if the input source is connected to an HDMI IN.
■
Language
(North American models)
`
English, Deutsch, Français, Español, Italiano,
Nederlands, Svenska
Nederlands, Svenska
(European and Asian models)
`
English, Deutsch, Français, Español, Italiano,
Nederlands, Svenska,
Nederlands, Svenska,
中文
This setting determines the language used for the on-
screen setup menus.
screen setup menus.
Main menu
Hardware Setup
Remote ID
■
Remote ID
`
1, 2, or 3
When several Onkyo components are used in the same
room, their remote ID codes may overlap. To differentiate
the AV receiver from the other components, you can
change its remote ID from “1”, to “2” or “3”.
room, their remote ID codes may overlap. To differentiate
the AV receiver from the other components, you can
change its remote ID from “1”, to “2” or “3”.
Note
• If you do change the AV receiver’s remote ID, be sure to change
the remote controller to the same ID (see below), otherwise, you
won’t be able to control it with the remote controller.
won’t be able to control it with the remote controller.
Changing the remote controller’s ID
Multi Zone
■
Zone 2 Out, Zone 3 Out
`
Fixed:
The Zone 2/3 volume must be set on the amp in that
zone.
zone.
`
Variable:
The Zone 2/3 volume can be set on the AV receiver.
If you’ve connected your Zone 2/3 speakers to an amp
with no volume control, set the “Zone 2 Out” and
“Zone 3 Out” setting, respectively, to “Variable” so that
you can set the volume, balance, and tone of zone 2 and
volume of zone 3 on the AV receiver.
with no volume control, set the “Zone 2 Out” and
“Zone 3 Out” setting, respectively, to “Variable” so that
you can set the volume, balance, and tone of zone 2 and
volume of zone 3 on the AV receiver.
■
Zone 2 Maximum Volume,
Zone 3 Maximum Volume
Zone 3 Maximum Volume
`
Off, 50 to 99 (Absolute display)
`
Off, –32dB to +17dB (Relative display)
With this setting, you can limit the maximum volume for
Zone 2/3.
Zone 2/3.
■
Zone 2 Power On Volume,
Zone 3 Power On Volume
Zone 3 Power On Volume
`
Last, Min, 1 to 99 or Max (Absolute display)
`
Last
, –
QdB, –81dB to +18dB (Relative display)
This setting determines what the volume will be for
Zone 2/3 each time the AV receiver is turned on.
To use the same volume level as when the AV receiver
was last turned off, select “Last”.
The “Zone 2 Power On Volume” and “Zone 3 Power
On Volume” cannot be set higher than the “Zone 2
Maximum Volume” and “Zone 3 Maximum Volume”
setting.
Zone 2/3 each time the AV receiver is turned on.
To use the same volume level as when the AV receiver
was last turned off, select “Last”.
The “Zone 2 Power On Volume” and “Zone 3 Power
On Volume” cannot be set higher than the “Zone 2
Maximum Volume” and “Zone 3 Maximum Volume”
setting.
Tuner
For AM/FM tuning to work properly, you must specify the
AM/FM frequency step used in your area. Note that when
this setting is changed, all radio presets will be deleted.
AM/FM frequency step used in your area. Note that when
this setting is changed, all radio presets will be deleted.
■
AM/FM Frequency Step (North American
models)
models)
`
10kHz/200kHz:
`
9kHz/50kHz:
Select the frequency step according to your area.
■
AM Frequency Step (European and Asian
models)
models)
`
10kHz:
`
9kHz:
Select the frequency step according to your area.
Hardware Setup
1
While holding down
RECEIVER, press and hold
down
SETUP until RECEIVER lights (about 3
seconds) (
).
2
Use the number buttons to enter ID 1, 2, or 3.
RECEIVER flashes twice.
RECEIVER flashes twice.