ONKYO TX-NR3009 Mode D'Emploi
83
En
The AV receiver’s remote controller can learn the
commands of other remote controllers. By transmitting,
for example, the Play command from your CD player’s
remote controller, the supplied remote controller can learn
it, and then reproduce the exact same command when its
1 is pressed in CD remote mode.
This is useful when you’ve entered the appropriate remote
control code (
commands of other remote controllers. By transmitting,
for example, the Play command from your CD player’s
remote controller, the supplied remote controller can learn
it, and then reproduce the exact same command when its
1 is pressed in CD remote mode.
This is useful when you’ve entered the appropriate remote
control code (
) but some buttons don’t work
as expected.
Note
• The following buttons cannot learn new commands:
8RECEIVER, ALL OFF, MY MOVIE, MY TV, MY MUSIC,
REMOTE MODE, MODE, HOME.
REMOTE MODE, MODE, HOME.
• The remote controller can learn approximately 70 to 90
commands, although this will be less if commands that use a lot
of memory are learned.
of memory are learned.
• Remote controller buttons such as Play, Stop, and Pause are
preprogrammed with commands for controlling Onkyo CD
players, cassette decks, and DVD players. However, they can
learn new commands, and you can restore the preprogrammed
commands at any time by resetting the remote controller
(
players, cassette decks, and DVD players. However, they can
learn new commands, and you can restore the preprogrammed
commands at any time by resetting the remote controller
(
).
• To overwrite a previously acquire command, repeat this
procedure.
• Depending on the remote controller that you are using, there may
be some buttons that won’t work as expected, or even some
remotes with which learning is impossible.
remotes with which learning is impossible.
• Only commands from infrared remote controllers can be acquire.
• When the remote controller runs out of batteries, all commands
• When the remote controller runs out of batteries, all commands
acquired will be lost and will have to be learned all over again.
Therefore, do not discard your other remote controllers.
Therefore, do not discard your other remote controllers.
■
Deleting Acquired Commands
1. While holding down REMOTE MODE for the mode
from which you want to delete a command, press and
hold down TV until the REMOTE MODE button
lights (about 3 seconds).
hold down TV until the REMOTE MODE button
lights (about 3 seconds).
2. Press REMOTE MODE or the button from which you
want to delete the commands.
The REMOTE MODE button flashes twice.
When you press REMOTE MODE, all commands
learned in that mode will be deleted.
The REMOTE MODE button flashes twice.
When you press REMOTE MODE, all commands
learned in that mode will be deleted.
Learning Commands
1
While holding down
REMOTE MODE for the
mode in which you want to use the command, press
and hold down
8RECEIVER until the REMOTE
MODE button lights (about 3 seconds).
2
On the supplied remote controller, press the
button to which you want to assign the new
command.
button to which you want to assign the new
command.
3
Point the remote controllers at each other, within
about 4 inches (10 cm) apart, and then press and
hold the button whose command you want to
acquire until the
about 4 inches (10 cm) apart, and then press and
hold the button whose command you want to
acquire until the
REMOTE MODE button flashes.
If the command is learned successfully, the
REMOTE MODE button flashes twice.
REMOTE MODE button flashes twice.
4
To learn more commands, repeat steps 2 and 3.
Press any
REMOTE MODE when you’ve finished.
The
REMOTE MODE button flashes twice.
8RECEIVER
REMOTE
MODE
PO
WER
SLEEP
DIMMER
SUR
MODE
VIDEO-1
VIDEO-2
TA
PE
DV
D
C D
C D
DV
D
TU
NER
TUNER
PHONO
INPUT SELECT
OR
DISC
VO
LUME
CH SEL
PRESET
UT
ING
TEST
TO
N
E
MUL
TI-CH
INPUT
GR
OUP
Within about
4 inches (10 cm)
4 inches (10 cm)
Supplied remote
controller
controller