ONKYO TX-NR609 Mode D'Emploi

En

If you connect a video component to a component video 
input, you must assign that input to an input selector. For 
example, if you connect your Blu-ray Disc/DVD player to 
COMPONENT VIDEO IN 2, you must assign “IN2” to 
the “BD/DVD” input selector. 
Here are the default assignments.

■

BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, 
TV/CD, PORT

`

IN1, IN2:

Select a corresponding component video input to 
which the video component has been connected.

`

- - - - -:

Select if you are using the HDMI output, not the 
component video output, to output composite video 
and component video sources.

• If you connect a component (such as UP-A1 Dock with docked 

iPod/iPhone) to the UNIVERSAL PORT jack, you cannot 
assign any input to the “PORT” selector.

• The  “AUX” selector is fixed at the “- - - - -” option.
• The  “TUNER” selector cannot be assigned and is fixed at the 

“- - - - -” option.

If you connect a component to a digital audio input, you 
must assign that input to an input selector. For example, if 
you connect your CD player to the OPTICAL IN 1, you 
must assign “OPTICAL1” to the “TV/CD” input 
selector. 
Here are the default assignments.

■

BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, 
TV/CD, PORT

`

COAXIAL1, COAXIAL2, OPTICAL1, 
OPTICAL2:

Select a corresponding digital audio input to which 
the component has been connected.

`

- - - - -:

Select if the component is connected to an analog 
audio input.

• When an HDMI IN is assigned to an input selector in “HDMI 

Input” (

page 44), the same HDMI IN will be set as a priority 

in this assignment. In this case, if you want to use the coaxial or 
optical audio input, make the selection in the “Audio Selector” 
(

page 54).

• Available sampling rates for PCM signals from a digital input 

(optical and coaxial) are 32/44.1/48/88.2/96 kHz/16, 20, 24 bit.

• If you connect a component (such as UP-A1 Dock with docked 

iPod/iPhone) to the UNIVERSAL PORT jack, you cannot 
assign any input to the “PORT” selector.

• The  “AUX” selector is fixed at the “- - - - -” option.
• The  “TUNER” selector cannot be assigned and is fixed at the 

“- - - - -” option.

Here you can check the settings made by Audyssey 2EQ 
Room Correction and Speaker Setup function, or set them 
manually, which is useful if you change one of the 
connected speakers after using Audyssey 2EQ Room 
Correction and Speaker Setup function.

• These settings are not available in either of the following cases:

– a pair of headphones is connected.
– the  “Audio TV Out” setting is set to “On” (

– “HDMI Control (RIHD)” is set to “On” (

page 56) and 

you’re listening through your TV speakers.

If the impedance of any speaker is 4 ohms or more but less 
than 6, set the minimum speaker impedance to 4 ohms.
If you bi-amp the front speakers, you must change the 
“Speakers Type (Front)” setting (

page 46). For 

hookup information, see “Bi-amping the Front Speakers” 
(

page 15).

• When bi-amping is used, the AV receiver is able to drive up to 

5.1 speakers in the main room.

• Before you change these settings, turn down the volume.

Some of the settings in this section are set automatically 
by Audyssey 2EQ

®

 Room Correction and Speaker 

Setup (

page 31).