ONKYO TX-NR609 Mode D'Emploi
![ONKYO](https://files.manualsbrain.com/attachments/8aea18be949e459a0f55b8379882c4c18cf8698b/common/fit/150/50/cdcf544ed9e39671a87280176f4bdeefe94b330d63641d63ea2dc47d350c/brand_logo.png)
59
En
Main menu
Remote Controller Setup
Remote Mode Setup
With this preference, you can protect your settings by
locking the setup menus.
locking the setup menus.
Main menu
Lock Setup
■
Setup
`
Locked
`
Unlocked
When “Locked” is selected, the setup menus will be
locked and you cannot change any setting.
locked and you cannot change any setting.
You can change various audio settings from the Home
menu (
menu (
page 40).
Note
• These settings are not available in either of the following cases:
– a pair of headphones is connected.
– the “Audio TV Out” setting is set to “On” (
– the “Audio TV Out” setting is set to “On” (
page 57).
– “HDMI Control (RIHD)” is set to “On” (
you’re listening through your TV speakers.
Tone Control Settings
■
Bass
`
–10dB to 0dB to +10dB in 2 dB steps.
You can boost or cut low-frequency sounds output
from the front speakers.
from the front speakers.
■
Treble
`
–10dB to 0dB to +10dB in 2 dB steps.
You can boost or cut high-frequency sounds output
from the front speakers.
from the front speakers.
You can adjust the bass and treble for the front speakers,
except when the Direct, Pure Audio (European,
Australian and Asian models) or THX listening mode is
selected.
except when the Direct, Pure Audio (European,
Australian and Asian models) or THX listening mode is
selected.
Operating on the AV receiver
Note
• To bypass the bass and treble tone circuits, select the Direct,
Pure Audio (European, Australian and Asian models) or THX
listening mode.
listening mode.
Speaker Levels
■
Subwoofer Level
`
–15dB to 0dB to +12dB in 1 dB steps.
■
Center Level
`
–12dB to 0dB to +12dB in 1 dB steps.
You can adjust the volume of each speaker while listening
to an input source.
These temporary adjustments are cancelled when the AV
receiver is set to standby. To save the setting you made
here, go to “Level Calibration” (
to an input source.
These temporary adjustments are cancelled when the AV
receiver is set to standby. To save the setting you made
here, go to “Level Calibration” (
setting the AV receiver to standby.
Note
• You cannot use this function while the AV receiver is muted.
• Speakers that are set to “No” or “None” in
• Speakers that are set to “No” or “None” in
page 46) cannot be adjusted.
Audyssey
■
Audyssey
■
Dynamic EQ
page 50).
■
Dynamic Volume
Note
• These technologies can be used when all the following
conditions are met:
– Room Correction and Speaker Setup is completed. Note that
– Room Correction and Speaker Setup is completed. Note that
“Audyssey” requires the “Audyssey 2EQ Full Calibration”
method.
method.
– Any listening mode other than Direct or Pure Audio
(European, Australian and Asian models) is selected.
– A pair of headphones is not connected.
• The setting is stored individually for each input selector.
Remote Controller Setup
Lock Setup
Using the Audio Settings
1
Press
RECEIVER followed by HOME.
2
Use
q/w and ENTER to select “Audio”, and then
use
q/w/e/r to make the desired selection.
1
Press
TONE repeatedly to select either “Bass” or
“Treble”.
2
Use
+ and – to adjust.