ONKYO TX-NR801 Manuel D'Instructions
30
Selecting the Appropriate Setting for Your Connections
In this section, you will perform the initial settings for
the following scenarios.
• When the impedances for speakers connected to the
the following scenarios.
• When the impedances for speakers connected to the
TX-NR801/TX-NR801E are between 4 and 6
Ω (See
page 18).
• When connecting speakers to the ZONE 2
SPEAKERS terminals (See page 66).
• When operating the remote controller using the IR IN
terminal (See page 69).
• When you want to fix the TV Format setting to PAL or
NTSC.
• When you want to fix the AM Frequency Step setting
to 9 kHz or 10 kHz.
Note:
The settings within the Hardware Setup Menu will need
to be made before you use your TX-NR801/
TX-NR801E for the first time. Once you have selected
one of the Hardware Setup menu items, the setting will
not be displayed again when you enter the Basic Menu.
To change the setting at a later date, select the Advanced
Menu to display the Hardware Setup Menu.
The settings within the Hardware Setup Menu will need
to be made before you use your TX-NR801/
TX-NR801E for the first time. Once you have selected
one of the Hardware Setup menu items, the setting will
not be displayed again when you enter the Basic Menu.
To change the setting at a later date, select the Advanced
Menu to display the Hardware Setup Menu.
If you want to perform these operations using the remote
controller, first press the RCVR button.
controller, first press the RCVR button.
Speaker Impedance Sub-menu
Use this sub-menu to set the impedance level of the
TX-NR801/TX-NR801E to match the specifications of
the speakers you are using.
TX-NR801/TX-NR801E to match the specifications of
the speakers you are using.
a. Minimum
6 ohms (default): Select when the impedances of all
speakers are between 6 and 16
speakers are between 6 and 16
Ω.
4 ohms: Select when the impedance of even one
speaker is between 4 and 6
speaker is between 4 and 6
Ω.
Note:
Before you change this setting, be sure to first lower the
volume at the TX-NR801/TX-NR801E to the minimum
level.
Before you change this setting, be sure to first lower the
volume at the TX-NR801/TX-NR801E to the minimum
level.
Surr Back/Zone 2 Sub-menu
Hardware Setup
1
Display the main menu.
Press the SETUP button on the front panel or
SETUP button on the remote controller to display
the main menu on the monitor and front display.
Press the SETUP button on the front panel or
SETUP button on the remote controller to display
the main menu on the monitor and front display.
DSP
A-FO RM LISTENING MODE MEMORY
THX
SURROUND
DIRECT / PURE AUDIO
STEREO
FM MODE
MEMORY
ENTER
RE TURN
SETUP
TUNING
PRESET
SETUP/ENTER/
RETURN/Cursor
RETURN/Cursor
/ /
/
[ENTER]Quit:[SETUP]
Advanced Menu
0.Hardware Setup
1.Speaker Setup
2.Input Setup
3.Audio Adjust
4.Preference
5.Network Setup
1.Speaker Setup
2.Input Setup
3.Audio Adjust
4.Preference
5.Network Setup
→Basic Menu
0.Hardware Setup
1.Speaker Impedance
2.Surr Back/Zone2
3.Remote Setup
4.TV Format
5.AM Frequency Step
2.Surr Back/Zone2
3.Remote Setup
4.TV Format
5.AM Frequency Step
[ENTER]Quit:[SETUP]
2
Use the
and
cursor buttons to select
“0. Hardware Setup” and then press the
ENTER button.
The “Hardware Setup” menu appears.
ENTER button.
The “Hardware Setup” menu appears.
3
Use the
and
cursor buttons to select
an item and then press the ENTER button.
4
Use the
and
cursor buttons to select
an item and then use the
and
cursor
buttons to set the desired value.
5
Press the SETUP button to exit the Setup
menu.
Press the RETURN button to return to the previ-
ous menu.
menu.
Press the RETURN button to return to the previ-
ous menu.
0-1.Speaker Impedance
a.Minimum :6 ohms
a.Minimum :6 ohms
Quit:[SETUP]
0-2.Surr Back/Zone2
a.Surr Back/Zone2
:Zone2
a.Surr Back/Zone2
:Zone2
Quit:[SETUP]