ONKYO TX-SR607 Manuel D’Utilisation
43
If the impedance of any speaker is 4 ohms or more but
less than 6, set the minimum speaker impedance to 4
ohms.
If you’ve connected your front speakers to the FRONT
L/R and SURR BACK L/R terminal posts for bi-amping,
you must change the “Speaker Type” setting. For hookup
information, see “Bi-amping the Front Speakers” on
page 19.
less than 6, set the minimum speaker impedance to 4
ohms.
If you’ve connected your front speakers to the FRONT
L/R and SURR BACK L/R terminal posts for bi-amping,
you must change the “Speaker Type” setting. For hookup
information, see “Bi-amping the Front Speakers” on
page 19.
Notes:
• When bi-amping is used, the AV receiver is able to
• When bi-amping is used, the AV receiver is able to
drive up to 5.1 speakers in the main room.
• Before you change these settings, turn down the
volume.
Powered Zone 2
Note:
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
Speaker Settings
1
Press the [RECEIVER] button,
followed by the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make
sure the appropriate external input is
selected on your TV.
followed by the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make
sure the appropriate external input is
selected on your TV.
2
Use the Up and Down [
q]/[w] but-
tons to select “2. Speaker
Setup”, and then press [ENTER].
The “Speaker Setup” menu appears.
Setup”, and then press [ENTER].
The “Speaker Setup” menu appears.
3
Use the Up and Down [
q]/[w] but-
tons to select “1. Speaker Set-
tings”, and then press [ENTER].
The “Speaker Settings” menu appears.
tings”, and then press [ENTER].
The “Speaker Settings” menu appears.
If you change these settings, you must run the
Audyssey 2EQ™ Room Correction and Speaker Setup
again (see page 46).
Audyssey 2EQ™ Room Correction and Speaker Setup
again (see page 46).
2. Speaker
Setup
1. Speaker
Settings
2. Speaker
Configuration
3. Speaker
Distance
4. Level
Calibration
5. Equalizer
Settings
2–1. Speaker
Settings
Speaker Impedance
Speaker Type
Powered Zone 2
Speaker Type
Powered Zone 2
Surr Back/Front High
6ohms
Normal
Not Act
Surr Back
4
Use the Up and Down [
q]/[w] but-
tons to select “Speaker Imped-
ance”, and then use the Left and
Right [
ance”, and then use the Left and
Right [
e]/[r] buttons to select:
4ohms: Select if the impedance of any
speaker is 4 ohms or more but
less than 6.
less than 6.
6ohms: Select if the impedances of all
speakers are between 6 and
16 ohms.
16 ohms.
Note:
North American/Taiwan models do not
support speakers with an impedance of
less than 6 ohms.
North American/Taiwan models do not
support speakers with an impedance of
less than 6 ohms.
5
Use the Up and Down [
q]/[w] but-
tons to select “Speaker Type”,
and then use the Left and Right
[
and then use the Left and Right
[
e]/[r] buttons to select:
Normal: Select this if you’ve con-
nected your front speakers
normally.
normally.
Bi-Amp:Select this if you’ve con-
nected your front speakers for
bi-amped operation.
bi-amped operation.
Note:
Powered Zone 2 cannot be used if
“Speaker Type” is set to “Bi-Amp”.
Powered Zone 2 cannot be used if
“Speaker Type” is set to “Bi-Amp”.
6
Use the Up and Down [
q]/[w] but-
tons to select “Surr Back/Front
High”, and then use the Left and
Right [
High”, and then use the Left and
Right [
e]/[r] buttons to select:
Front High:
FRONT HIGH L/R speakers
can be used.
can be used.
Surr Back:
SURR BACK L/R speakers
can be used.
can be used.
Note:
• If the “Speaker Type” setting is set to
• If the “Speaker Type” setting is set to
“Bi-Amp”, or Powered Zone 2 is set
to “Not Act”, this setting cannot be
selected.
to “Not Act”, this setting cannot be
selected.
7
Press the [SETUP] button.
The setup menu closes.
The setup menu closes.