ONKYO TX-SR800 Manuel D'Instructions
33
3. Turn on the connected component and start playing
the desired media.
4. If necessary, adjust the output level of each speaker
as desired (see page 32).
Adjust the volume at each speaker so that all the volumes sound
at the same level at the listening position. For the front right,
front left, center, surround right, surround left, surround back
right, and surround back left speakers, the output levels can be
adjusted between –12 and +12 decibels. The subwoofer can be
adjusted between –30 and +12 decibels.
at the same level at the listening position. For the front right,
front left, center, surround right, surround left, surround back
right, and surround back left speakers, the output levels can be
adjusted between –12 and +12 decibels. The subwoofer can be
adjusted between –30 and +12 decibels.
Note:
If you change the speaker levels in step 4 above, these new levels for
multichannel sources will have no effect on the settings at Setup Menu
If you change the speaker levels in step 4 above, these new levels for
multichannel sources will have no effect on the settings at Setup Menu
→ Speaker Setup Menu → Level Calibration Sub-menu (see page 45).
5. Adjust the volume with the MASTER VOLUME dial (or
the VOL
buttons on the remote controller.)
Changing the listening mode:
Each time you press the DIRECT/PURE AUDIO button on the front
panel, the display changes between “Direct”
panel, the display changes between “Direct”
“Pure Audio.”
When using a remote controller, press PURE A or DIRECT.
Using the tone cotrol:
1. Press the SURROUND button on the front panel (or the
SURR button on the remote controller) to display
“Tone On.”
“Tone On.”
2. Adjust the tone at Setup Menu
→
Audio Adjust Menu
→
Tone Control Sub-menu (see page 53).
Press the DIRECT/PURE AUDIO button on the front panel (or
the DIRECT button on the remote controller) to turn off the tone
control.
the DIRECT button on the remote controller) to turn off the tone
control.
Changing the audio mode
Press the AUDIO SELECTOR button on the front panel (or AUDIO
SEL button on the remote controller) to change the audio mode.
Each time the button is pressed, the mode changes from “Auto”
SEL button on the remote controller) to change the audio mode.
Each time the button is pressed, the mode changes from “Auto”
→
“Multich”
→ “Analog” and back to “Auto.” The “Auto” audio mode
is recommended for normal circumstances.
Auto (automatic detection): With this setting, the TX-SR800
automatically detects whether the input signal is digital or analog.
When a digital signal is not input, then the analog signal is played.
This setting only appears if a digital input is selected for the Digital
Input setting at Setup Menu
automatically detects whether the input signal is digital or analog.
When a digital signal is not input, then the analog signal is played.
This setting only appears if a digital input is selected for the Digital
Input setting at Setup Menu
→ Input Setup Menu → Digital Setup
Sub-menu (see page 46).
Multich (Multichannel): Select this setting to play back the input
from the component connected to the MULTI CHANNEL INPUT
port. This setting only appears if “Yes” is selected for the
Multichannel setting at Setup Menu
from the component connected to the MULTI CHANNEL INPUT
port. This setting only appears if “Yes” is selected for the
Multichannel setting at Setup Menu
→ Input Setup Menu →
Multichannel Setup Sub-menu (see page 47).
Analog: Select this setting to play back the input from a source
component connected to analog audio input jacks. With this setting,
even if a digital signal is input from the same component, only the
analog signal will be output.
component connected to analog audio input jacks. With this setting,
even if a digital signal is input from the same component, only the
analog signal will be output.
Enjoying the multichannel output
Before starting operations, first make sure that the multichannel
connection is properly made and that “Yes” is selected for the
Multichannel setting at Setup Menu
connection is properly made and that “Yes” is selected for the
Multichannel setting at Setup Menu
→ Input Setup Menu →
Multichannel Setup Sub-menu (see page 47).
1. Press the input source button for the component
connected to the MULTI CHANNEL INPUT on the rear
of the TX-SR800.
of the TX-SR800.
2. Select “Multich” using the AUDIO SELECTOR button
on the front panel (or AUDIO SEL button on the remote
controller).
controller).
Enjoying music or videos with the TX-SR800
TX-SR800
Remote controller
TX-SR800
Remote controller
STANDBY/ON
STANDBY
PHONES
MASTER VOLUME
TAPE
TUNER
PHONO
C D
VIDEO
4
VIDEO
5
VIDEO
3
VIDEO
2
VIDEO
1
DVD
OFF
ZONE
2
REC OUT
DISPLAY
DIMMER
AUDIO
SELECTOR
ZONE
2 (
)
GRN
REC (
)
RED
VCR
2
VCR
1
S VIDEO
AUDIO
VIDEO
L
R
DIGITAL
VIDEO
5 INPUT
OFF
ON
POWER
TX-SR800
PURE AUDIO
UPSAMPLING
CLEAR
DSP
A-FO RM LISTENING MODE MEMORY
THX
SURROUND
DIRECT / PURE AUDIO
STEREO
FM MODE
MEMORY
ENTER
RE TURN
SETUP
TUNING
PRESET
AUDIO SELECTOR
DIRECT
AUDIO SEL
MASTER VOLUME
DIRECT/PURE AUDIO
VOL
AUDIO
SELECTOR
AUDIO
SELECTOR
Input source buttons
TX-SR800
Remote controller
MASTER VOLUME
DIRECT / PURE AUDIO
TX-SR800
Remote controller