Behringer GMX110 Mode D'Emploi

V-TONE GMX110/GMX112/GMX210/GMX212/GMX1200H

2. CONTROL ELEMENTS AND CONNECTIONS

2.2 Rear panel

Connect the stereo jack connector of the provided

footswitch to the FOOTSWITCH connector. The footswitch

has several functions: it lets you switch between two

channels, and it also lets you activate/deactivate an effect.

Additionally, the tuner can also be activated using the

footswitch. To do that, keep the CHANNEL key pressed

for about 2 seconds.
MIDI IN. This connector lets you remotely control your

V-TONE via MIDI. You can activate/deactivate effects or

switch between channels. You can use effect bypass via

program changes and parameter edits as well as edit the

presets via controllers (also see sections 6.3 and 7.1).
You can connect two external loudspeakers (L/R) to the

LOUDSPEAKER connectors (GMX212 and GMX1200H).

The outputs deliver 60 W into 8 W per channel. For optimum

performance, please only connect loudspeakers with a

minimum impedance of 8 W each (see also section 6.2).

When these connectors are used the internal loudspeakers

are automatically disconnected.

The GMX210 features no external loudspeaker

connectors. The loudspeaker connector on the

GMX110 and GMX112 is described under

The PHONES connector lets you monitor the signal from

your V-TONE with standard headphones. The BEHRINGER

HP series is well suited for this, for example. When the

PHONES connector is used, the internal loudspeakers and

speaker outputs are disconnected.
Those signals that are connected to the SLAVE IN

connectors are directly routed to the V-TONEs power

amp. This way, you can connect an external guitar preamp

or modeling amp (e. g. V-AMP 2 or V-AMP PRO) without

using the internal preamp on your V-TONE.

The GMX110 and GMX112 feature no SLAVE IN

connectors.
You can take the stereo signal of your V-TONE at the

TAPE outputs (RCA) and record it, for example.
The TAPE inputs (RCA) let you feed an additional stereo

signal into your V-TONE. You can play along to the beat of

a drum computer or play to music from a CD or MD player.
You can take the stereo signal of your V-TONE at the LINE

outputs to record it or route it to a P.A. system. This output

is independent from the MASTER control and does not

render the AUX signal. Additionally, its frequency response

is corrected (speaker simulation).

The GMX110 and GMX112 feature no LINE outputs.
Use the AUX IN control to adjust the volume of the signal

that is fed in via the AUX IN connectors (e. g. drum

computer, playback).

On the GMX110 and GMX112, this control is called

TAPE INPUT. It regulates the volume of the signal

fed in at the TAPE IN connectors.
The AUX IN lets you feed an additional stereo signal into

the amp. This way, you can play to a backing track that

supports you on-stage but should not be audible via the

LINE outputs connecting the GMX210/GMX212 to the P.A.

system. Additionally, you can use AUX IN together with

the INSERT SEND as a parallel insert loop. To do that,

connect the INSERT SEND to the input of your effects

device; connect the AUX IN (TAPE IN on the GMX110 and

GMX112) to the output of your effects unit (the INSERT

RETURN connector should not be in use!). This way, the

signal flow in your V-TONE is not interrupted. With the

AUX IN control, you can determine the extent to which the

external effects unit alters the original signal. Keep in mind

that the effects unit should be set up to 100% effects

signal (100% wet).

Your V-TONE features a serial insert loop that can be used

to connect external effects (e. g. a wah-wah pedal).

Connect the SEND connector on the V-TONE to the input

of your effects unit. The SEND connector is tapped into

directly before (i.e. pre) the digital signal processor (DSP)

of your V-TONE. Connect the output of your external effects

unit to the RETURN connector of your V-TONE.

You can use the INSERT SEND as a parallel output

without the effects. This is useful, for example,

when you want to record a dry guitar signal. As

long as the RETURN connector has nothing plugged

into it, the signal will not be interrupted internally.
Use the SPEAKER OUT connector to connect one additional

loudspeaker to your GMX110/GMX112. This loudspeaker

should have an impedance of 4 W. When this connector is

used, the internal loudspeaker is automatically muted.

Additional information about connecting an external

loudspeaker can be found in section 6.2.
FUSE RETAINER/VOLTAGE SELECTOR. Please make

sure that the voltage indicated by the voltage selector

matches the local voltage before you connect the unit to

the main power supply. Always replace blown fuses with

fuses of the same type and rating. Some units feature a

fuse retainer in which a selection between 230 V and 120

V is possible. Please be aware: When using your unit

outside of Europe with 120 V, a fuse with a higher rating is

required.
Power is supplied via an IEC connector. The matching

cable is provided with the unit.
SERIAL NUMBER.