Epson 1835 Guide D’Installation Rapide

Before using the projector, make sure you read the safety instructions in the 
User’s Guide on your projector CD.

Choose from the following connections:

Connect a computer using a USB cable.

Connect the square end of the USB cable to the projector’s  

 USB 

TypeB (square) port. Connect the flat end of the cable to any USB port on 
your computer.

 After turning on the projector, follow 

the on-screen instructions to install the Epson USB Display software 
(EMP_UDSE.EXE; only on first connection).

Note: If the software screen does not display automatically, open My 
Computer or Computer, then double-click EPSON_PJ_UD. If it still does not 
display, access the projector’s Extended menu and select USB Display as the 
USB Type B setting. See the User’s Guide on your projector CD for instructions.

 After turning on the projector, the setup folder 

for USB Display appears in the Finder. Double-click USB Display Installer and 
follow the on-screen instructions to install the Epson USB Display software 
(only on first connection).

Connect a computer using the VGA cable that came with the projector.

Connect one end of the cable to the projector’s Computer1 or Computer2 
port, and the other end to your computer’s  

 monitor port. If you are using 

a notebook, switch it to external display (see “Troubleshooting”). You can also 
connect an audio cable.

You can connect the projector wirelessly over an 802.11g, 802.11b, or 802.11n 
wireless network. See “Project wirelessly” for instructions.

You can connect the projector to your network using an Ethernet

®

 cable. 

See “Project over a wired network” on the back of this sheet for instructions.

Connect up to 5 video devices and use the Source Search button on the 
projector or remote control to switch between them. (All cables are optional).

Connect a digital camera, USB flash drive, USB storage device, or Epson 
document camera DC-06 to the projector’s USB TypeA (flat) port.

If you connect a digital camera, USB flash drive, or USB storage device, you can 
use the projector’s Slideshow feature. See the User’s Guide on your projector 
CD for details.

You can also connect an external monitor, external speakers, and a microphone 
to your projector to enhance your presentations. See the User’s Guide on your 
projector CD for details.

 

Turn on your computer or video source.

 

Plug in the projector.

 

The power light on the projector turns orange.

Open the A/V Mute slide all the way.

 Press 

the

power button on the projector or remote control.

 The 

power light flashes green, then stays on.

Note: To shut down the projector, press the

 

 The default language of the menu system is English. To select another 
language, press the Menu button on the remote control. Select 
Extended and press Enter. Select Language and press Enter. Select your 
language and press Enter. Press the Menu to exit the menu system. 

 

 If you don’t see an image, press the Source Search button on the 
projector or the remote control to select the image source.

 

 

 

 

 To raise the image, press the foot release button and lift the front of the 
projector. Release the button to lock the foot in position.

 

Rotate the focus ring to sharpen the image.

   

 

Turn the zoom ring to reduce or enlarge the image.

          

 

 If your image looks like

or

, you’ve placed the projector off to 

one side of the screen at an angle. Place it directly in front of the center 
of the screen, facing the screen squarely. Or press the   or   buttons on 
the projector to correct it.

 

 If your image looks like

or

, press the

or

buttons on the 

projector to correct it.

Make sure the batteries are installed as shown (two AA batteries).

For more information on using the remote control, see the User’s Guide on 
your projector CD.

Follow the steps here to connect the projector wirelessly over an 802.11g, 
802.11b, or 802.11n wireless network. You must install the optional Epson 
wireless LAN module (part number V12H418P12). Your computer must have 
a wireless card or built-in wireless interface, and be running Windows 7, 
Windows Vista

®

, Windows XP Professional x64, Windows XP, or Windows 2000, 

or Mac OS X 10.3 to 10.6.

Turn off the projector and unplug the power cord.

Slide the air filter cover latch and open the air filter cover.

 

 Remove the screw securing the wireless LAN module stopper, then 
remove the stopper.

 

Insert the wireless LAN module into the port.