FoneGEAR 976 Mode D'Emploi
Mini Blu Bluetooth Headset User Manual - Lightweight Wireless Headset User Manual
Charge headset before use (4 hours)
Turning On/Off Headset
To turn on headset: Press down on the P2 button for 2 or 3 seconds until the Blue LED flashes (You may hear two high tones
from the loudspeaker), then release. It will indicate the standby mode by linking Blue LED.
To turn off headset: Press down on the P2 button for 2 seconds until the Red LED flashes. Both Red and Blue LED’s will stop
blinking (You may heard two low tones from the loudspeaker), and the headset will go into power off mode.
The red indicator light will flash slowly when the battery is low.
Pairing the Headset
*You are required to pair the headset with your mobile phone or other device before using it.
1. Ensure the headset is off, then press down the P2 button until the pairing mode (both Blue & Red-LED’s are flashing
alternately), then release. This will take about 6 seconds.
2. Initiate pairing process of your mobile phone. Refer to the manual of the mobile phone for the direction. You will see a new
item “BT headset” added in your Bluetooth device list after the searching process.
3. You will be asked to enter a pin code to complete the pairing. Enter 1234 and confirm. (Note: the 1234 is a default pin code
pre-stored in the Headset) The red indication will turn off and the blue indicator will flash slowly after the paring is completed
successfully.
4. Once the pairing is complete, the Red LED will turn off and the Blue LED will begin blinking, (indicating standby mode). If it is
not finished paring within 2 minutes, the headset will go into standby mode, and pairing is unavailable. You will need to restart
and repeat steps 1-3.
Making Calls
You are able to use the headset to make calls when it is paired successfully with your mobile phone.
Using voice dialing (please check your mobile phone instruction manual to see if this function is enabled): Press P2 button, wait
for a beep, and say the name pre-stored in the mobile phone of the person you want to call. Press P2 button again to cancel
voice dialing.
Using phone keys: Dial the number on the mobile phone as you usually do. Once the call has been set up, the voice will be
transmitted to the headset automatically.
Last call redial: Press and hold V (-) button for 3 seconds to redial the last number you called.
Answering/Ending Calls
When the headset has been paired with your mobile phone and is working in standby mode, you may hear a musical tone from
the loudspeaker and the Blue LED will flash quickly when the phone rings.
Press P2 button to answer the call
End calls by pressing P2 button while talking.
Adjust Volume
Adjust headset volume by pressing V (+) button for volume up and pressing V (-) button for volume down.
Charge headset before use (4 hours)
Turning On/Off Headset
To turn on headset: Press down on the P2 button for 2 or 3 seconds until the Blue LED flashes (You may hear two high tones
from the loudspeaker), then release. It will indicate the standby mode by linking Blue LED.
To turn off headset: Press down on the P2 button for 2 seconds until the Red LED flashes. Both Red and Blue LED’s will stop
blinking (You may heard two low tones from the loudspeaker), and the headset will go into power off mode.
The red indicator light will flash slowly when the battery is low.
Pairing the Headset
*You are required to pair the headset with your mobile phone or other device before using it.
1. Ensure the headset is off, then press down the P2 button until the pairing mode (both Blue & Red-LED’s are flashing
alternately), then release. This will take about 6 seconds.
2. Initiate pairing process of your mobile phone. Refer to the manual of the mobile phone for the direction. You will see a new
item “BT headset” added in your Bluetooth device list after the searching process.
3. You will be asked to enter a pin code to complete the pairing. Enter 1234 and confirm. (Note: the 1234 is a default pin code
pre-stored in the Headset) The red indication will turn off and the blue indicator will flash slowly after the paring is completed
successfully.
4. Once the pairing is complete, the Red LED will turn off and the Blue LED will begin blinking, (indicating standby mode). If it is
not finished paring within 2 minutes, the headset will go into standby mode, and pairing is unavailable. You will need to restart
and repeat steps 1-3.
Making Calls
You are able to use the headset to make calls when it is paired successfully with your mobile phone.
Using voice dialing (please check your mobile phone instruction manual to see if this function is enabled): Press P2 button, wait
for a beep, and say the name pre-stored in the mobile phone of the person you want to call. Press P2 button again to cancel
voice dialing.
Using phone keys: Dial the number on the mobile phone as you usually do. Once the call has been set up, the voice will be
transmitted to the headset automatically.
Last call redial: Press and hold V (-) button for 3 seconds to redial the last number you called.
Answering/Ending Calls
When the headset has been paired with your mobile phone and is working in standby mode, you may hear a musical tone from
the loudspeaker and the Blue LED will flash quickly when the phone rings.
Press P2 button to answer the call
End calls by pressing P2 button while talking.
Adjust Volume
Adjust headset volume by pressing V (+) button for volume up and pressing V (-) button for volume down.