Canon VB-H651V Manuel

Network Camera

 

/

 

 

/

 

 Installation Guide

Installation Guide, keep it in a readily accessible location for future reference. This camera is 
for indoor use only.
* Some cameras are not available  in certain countries or regions.

   To reduce a risk of fire or electric shock, do not expose this product  to rain or 

moisture.

   Request a professional installer for all installation work. Never try to install the 

camera yourself. Doing so may result in unforeseen accidents such as dropping 

the camera or electric shock.

Camera, Screws (M4) x 3  

Template 

Installation Guide 

Setup CD-ROM 

Warranty Card 

   (This document)

Safety Wire, Screws (M3) x 1  

Ceiling Plate 

Notice

Audio Interface Cable 

 

  Power Connector 

 

  Dedicated wrench

Camera specific functions will be listed using the symbols below.

: VB-H651V   

: VB-M641V   

: VB-M640V

The following accessories can be purchased separately as necessary. Some accessories are not 

available in certain countries or regions.

Dedicated accessory used to install the camera recessed into a ceiling.

Dedicated accessory used to install the camera recessed into a ceiling. The part projecting out 

within the ceiling can be covered.

Dedicated accessory used to install the camera to the end of pipe that extends from high ceilings, 

such as in big-box stores.

Smoked dome cover.

 

Dedicated AC adapter for this camera.

BIE-7150-000

© CANON INC. 2016 

Printed in Japan

This Installation Guide uses the following symbols to indicate important information the user should 
know in order to use the product safely. Explanations are provided for each symbol so that users 
will understand the level of importance for each. Be sure to observe these items.

 

Failure to follow the instructions accompanied by this symbol may result 

in death or serious injury.

 

Failure to follow the instructions accompanied by this symbol may result in 

injury.

Failure to follow the instructions accompanied by this symbol may result 

in property damage. 

 

Do not install in the following places:

 

•  Places in direct sunlight, near heat-generating objects, or locations subject to high 

temperatures 

•  Places near fire sources or flammable solvents (alcohol, thinner, fuel, etc.) 

•  Humid or dusty places 

•  Places subject to oily smoke or steam 

•  Places subject to sea air

•  Confined or enclosed places

Failure to do so may result in fire or electric shock.

Notes on Power Supply

•  

 

 

Only use the dedicated AC adapter (sold separately) for AC power.

•  Do not set any heavy objects on the power cable (or the LAN cable for a PoE power 

supply).

•  Do not pull, forcibly bend, scratch, or modify the power cable (or the LAN cable for a 

PoE power supply).

•  

 

 

Do not cover or wrap the AC adapter (sold separately) with cloth or 

blankets.

Failure to do so may result in fire or electric shock.

 

For installation or inspection of this camera, consult the dealer where you purchased 

the product.

 

•  This installation should be made by a qualified service person and should conform to 

all local codes. 

•  When installing, make sure the surface is capable of withstanding the total weight of the 

camera and accessories, and sufficiently reinforce if necessary.

•  Be sure to use installation screws designed for the type of surface the camera is to be 

installed. 

•  Periodically check the parts and screws for rust and loosening, in order to prevent 

injuries and equipment damage due to falling items.

•  Do not install in unstable places, places subject to significant vibration or impact, or 

places subject to salt damage or corrosive gas.

•  Be sure to attach the safety wire when installing the camera.

Failure to do so may result in the camera falling or other accidents.

•  Do not touch the edges of metal parts with bare hands.

•  Be careful not to get your fingers caught when installing.

Failure to do so may result in injuries.

•  Do not move the lens unit by hand.

•  Do not install on an unstable surface.

•  To maximize shock resistant specifications, do not install on insufficiently strong 

surfaces or surfaces subject to significant vibration.

•  After turning off the power, do not turn the power on again for at least five seconds.

•  Take measures to remove static electricity before performing any procedures.

•  If there is condensation, please wait to power on until the condensation dissipates.

Failure to do so may result in malfunctions.

•  Take care not to damage wiring or piping.

Failure to do so may result in damage to the peripheral items.

 Important

•  We recommend the installation of a lightning arrester (a surge protection device) as a measure against 

failures caused by lightning strikes. Refer to our website for details.

 

•  If you discover defective conditions such as smoke, strange sounds, heat or strange 

odors, immediately stop using the camera and contact your nearest dealer.

Fire or electric shock may result from continued use of the product.

•  If thunder starts, stop installation or inspection etc. and do not touch the camera or 

continue connecting the cable.

•  Do not disassemble or modify the camera.

•  Do not damage the connecting cable.

•  Do not spray the camera with water, or otherwise make it wet.

•  Do not insert foreign objects such as water or metal into the camera.

•  Do not use flammable sprays near the camera.

•  Do not leave LAN cables, external power supply, or the power connector for the AC 

adapter (sold separately) connected when the camera is not in use for long periods.

•  Do not use flammable solvents such as alcohol, paint thinner or benzine when cleaning 

the camera.

Failure to do so may result in fire or electric shock.

150 (5.91)

R50 (R1.97)

Unit: mm (in.)

Unit: mm (in.)

Camera mounting tab slots

Camera mounting tabs

129 (5.08)

42.0

(1.65)

20.3

(0.80)

20.3

(0.80)

30.6 (1.20)

30.6 (1.20)

85.7 (3-3/8) 

(*3, *4)

46.0 (1-13/16) 

(*4)

10-  4.5 (  0.18) 

(*1, *2)

6.8 (0.27)

144 (5.67)

83.5 (3-9/32) 

(*4)

85.7 (3-3/8) 

(*3, *4)

3-M4 

(*5)

*1 Ceiling/Wall mount holes

*2 Junction box fixing holes

*3 Ceiling/Wall mount holes 

position

*4 Junction box fixing holes 

position

*5 Camera mounting holes

Serial_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 

MAC_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

3

8 9

10

11

2

1

5

4

6

7

1. Dome case lock screw / 2. Dome case / 3. Lens unit / 4. LED (Blue)* / 
5. Memory card slot / 6. Reboot switch / 7. Reset switch / 8. 100Base-TX LAN connector / 
9. Power connection terminal 

 

 / 10. Audio I/O terminal 

 

 / 

11. External device I/O terminals 

 

* On: when powered on, during reboot / Off: during normal use

Please refer to the installation procedures or the Appendix – Specifications for specifications not 

listed below.

Camera

Lens 

2.4x optical zoom (4x digital zoom) lens (electric drive)

Viewing Angle 
   

For 16:9 aspect ratios

   

   Horizontal: 122.1° (W) – 50.1° (T)

   

   Vertical: 65.8° (W) – 28.2° (T)

   

For 4:3 aspect ratios

   

   Horizontal: 89.2° (W) – 37.6° (T)

   

   Vertical: 65.8° (W) – 28.2° (T)

   

 

   

For 16:9 aspect ratios

   

   Horizontal: 111.5° (W) – 46.2° (T)

   

   Vertical: 60.5° (W) – 25.9° (T)

   

For 4:3 aspect ratios

   

   Horizontal: 111.5° (W) – 46.2° (T)

   

   Vertical: 81.7° (W) – 34.6° (T)

Min. Subject Illumination 
   

Day Mode (color):

   

   0.035 lux (F1.2, shutter speed 1/30 sec., when smart shade control is off, 50IRE)

   

Night Mode (monochrome):

   

   0.002 lux (F1.2, shutter speed 1/30 sec., when smart shade control is off, 50IRE)

   

When using the Dome Unit (Smoked) (sold separately)

   

Day Mode (color):

   

   0.07 lux (F1.2, shutter speed 1/30 sec., when smart shade control is off, 50IRE)

   

Night Mode (monochrome):

   

   0.004 lux (F1.2, shutter speed 1/30 sec., when smart shade control is off, 50IRE)

   

 

   

Day Mode (color):

   

   0.02 lux (F1.2, shutter speed 1/30 sec., when smart shade control is off, 50IRE)

   

Night Mode (monochrome):

   

   0.001 lux (F1.2, shutter speed 1/30 sec., when smart shade control is off, 50IRE)

   

When using the Dome Unit (Smoked) (sold separately)

   

Day Mode (color):

   

   0.04 lux (F1.2, shutter speed 1/30 sec., when smart shade control is off, 50IRE)

   

Night Mode (monochrome):

   

   0.002 lux (F1.2, shutter speed 1/30 sec., when smart shade control is off, 50IRE)

Pan Angle Range 

350° (±175°)

Tilt Angle Range 

150° (±75°)

Rotation Angle Range  350° (±175°)

Interface

Network Terminal 

LAN x 1 (RJ45, 100Base-TX (auto/full-duplex/half-duplex))

Audio Input Terminal 

 

 

3.5 mm ( 0.14 in.) mini-jack connector (monaural)

(Common for LINE IN & MIC IN)   

LINE IN (connect to an amplifier microphone) or 

   

 

MIC IN (connect to a microphone w/o amplifier)

   

 

Switch LINE IN/MIC IN in the setting page.

Audio Output Terminal 

 

 

3.5 mm ( 0.14 in.) mini-jack connector (monaural)

(LINE OUT) 

 

LINE OUT (connect to an amplifier speaker)

External Device I/O Terminal 

 

  Input x 2, Output x 2

Memory Card* 

microSD Memory Card, microSDHC Memory Card, microSDXC Memory Card Compatible. 
*  To insure reliability in the recording speed, it is recommended to use CLASS 10 rated 

products. Even when using CLASS 10 products, reliability cannot be guaranteed during 
heavy access loads (e.g., when recording and deleting data at the same time).

Others

Operating Environment 

 

  Temperature: 

   

 

   AC, DC, PoE: -10°C – +50°C (+14°F – +122°F)

   

 

Humidity: 5% – 85% (without condensation)

   

 

Temperature:

   

 

   PoE: -10°C – +50°C (+14°F – +122°F)

   

 

Humidity: 5% – 85% (without condensation)

Storage Environment 

Temperature: -30°C – +60°C (-22°F – +140°F)  
Humidity: 5% – 90% (without condensation)

Installation Method 

Ceiling mount/Surface mount

Power Supply 

 

  PoE:  PoE power supply via LAN connector (IEEE802.3at Type1 compliant)

   

 

AC Adapter: PA-V18 (100 – 240 V AC) (sold separately)

   

 

External power source: 24 V AC/12 V DC

   

 

PoE: PoE power supply via LAN connector (IEEE802.3at Type1 compliant)

Set the IP address and other network information on the camera using the “Camera Management 

Tool” on the Setup CD-ROM.

For details on how to operate the “Camera Management Tool”, please refer to the “Camera 

Management Tool User Manual”.

Remove the dome case, then remove the tape preventing the lens from rotating which was 

attached for shipping.

❶

❷

Dedicated 

wrench

Dedicated 

wrench

❸

❺

❹

Remove the dome case and place the memory card in the 

memory card slot.

To remove the memory card, push it in all the way until the 

card slightly pops out and remove.

 Important

•  Insert a memory card before installing the camera.
•  When using a memory card with the camera for the first time, 

it is recommended to format the card after inserting it into the 
camera (please refer to the “Operation Guide”).

•  Always unmount the memory card before removing it (please 

refer to the “Operation Guide”).

Memory card slot

Remove the dome case from the camera, then remove the dome cover holder and dome flange, 

and replace with the smoked dome.

 Important

•  Take care when replacing so as not to 

scratch the dome cover.

Dome flange

Dome cover

Dome cover holder

Dedicated wrench

Smoked dome cover

The contents of this guide are subject to change without any prior notice.

Power Consumption 

 

PoE: Max. approx. 8.4 W*

   

 

AC Adapter PA-V18: Max. approx. 9.9 W (100 V AC)

   

 

 

Max. approx. 9.8 W (240 V AC)

   

 

DC: Max. approx. 8.7 W

   

 

AC: Max. approx. 8.1 W

   

 

PoE: Max. approx. 8.4 W*

   

 

AC Adapter PA-V18:  Max. approx. 9.8 W (100 V AC)

   

 

 

 

Max. approx. 9.8 W (240 V AC)

   

 

DC: Max. approx. 8.7 W

   

 

AC: Max. approx. 8.1 W

   

 

PoE: Max. approx. 8.4 W*

   

* Class 0 power sourcing equipment (requests 15.4 W)

Weight 

 

  Approx. 890 g (1.97 lb.) 

   

 

 

Approx. 880 g (1.95 lb.) 

Impact Resistance 

IK10 (20J)