Canon VB-H652LVE Manuel

Network Camera

 

Installation Guide

Please be sure to read the “Safety Precautions” section for correct use. After reading this Installation 
Guide, keep it in a readily accessible location for future reference. 
* Some cameras are not available in certain countries or regions.

   

Request a professional installer for all installation work. Never try to install the camera yourself. 

Doing so may result in unforeseen accidents such as dropping the camera or electric shock.

Camera 

Template 

Installation Guide (This document) 

Setup CD-ROM 

Warranty Card 

Notice 

Ceiling Plate 

Safety Wire, Screws (M4) x 2  

Dedicated wrench

Power Connector

Audio Interface Cable 

BIE-7110-000

© CANON INC. 2016 

Printed in Japan

This Installation Guide uses the following symbols to indicate important information the user should know in order 
to use the product safely. Explanations are provided for each symbol so that users will understand the level of 
importance for each. Be sure to observe these items.

 

Failure to follow the instructions may result in death or serious injury.

Do not install in the following places:

 

•  Places in strong direct sunlight, near heat-generating objects, or locations subject to high 

temperatures 

•  Places near fire sources or flammable solvents (alcohol, thinner, fuel, etc.) 

•  Places subject to oily smoke or steam 

•  Confined or enclosed places

Failure to do so may result in fire or electric shock.

Notes on Power Supply

•  Only use the dedicated AC adapter (sold separately) for AC power.

•  Do not set any heavy objects on the power cable (or the LAN cable for a PoE+/PoE power supply).

•  Do not pull, forcibly bend, scratch, or modify the power cable (or the LAN cable for a PoE+/PoE power 

supply). 

•  Do not cover or wrap the AC adapter (sold separately) with cloth or blankets.

Failure to do so may result in fire or electric shock.

 

Failure to follow the instructions may result in injury.

For installation or inspection of this camera, consult the dealer where you purchased the product.

 

•  This installation should be made by a qualified service person and should conform to all local codes. 

•  When installing, make sure the surface is capable of withstanding the total weight of the camera and 

accessories, and sufficiently reinforce if necessary

•  Be sure to use installation screws designed for the type of surface the camera is to be installed.

•  Periodically check the parts and screws for rust and loosening, in order to prevent injuries and 

equipment damage due to falling items.

•  Do not install in unstable places, places subject to significant vibration or impact, or places subject to 

salt damage or corrosive gas.

•  Do not install in places subject to strong winds.

•  Do not install where snow can accumulate directly on the camera.

•  Be sure to attach the safety wire when installing the camera.

Failure to do so may result in the camera falling or other accidents.

•  Do not touch the edges of metal parts with bare hands.

•  Be careful not to get your fingers caught when installing.

Failure to do so may result in injuries.

•  Avoid looking directly at the infrared illumination at close distances

 for long periods of time.

Intense infrared illumination can cause eye damage.

Failure to follow the instructions may result in property damage. 

•  Do not install on an unstable surface.

•  To maximize shock resistant specifications, do not install on insufficiently strong surfaces or surfaces 

subject to significant vibration.

•  After turning off the power, do not turn the power on again for at least five seconds.

•  Take measures to remove static electricity before performing any procedures.

•  If there is condensation, please wait to power on, until the condensation dissipates.

•  Please waterproof and dust-proof camera as necessary, when installing outdoors.

Failure to do so may result in malfunctions.

•  Take care not to damage wiring or piping.

Failure to do so may result in damage to peripheral items.

 Important

We recommend the installation of a lightning arrester (a surge protection device) as a measure against failures caused by 
lightning strikes. Please refer to our website for details.

When installing the camea outdoors, observe the following precautions to retain 

waterproof/dustproof capabilities.

.

•  Use the sunshade cover (sold separately) when installing in a location with direct 

sunlight.

•  When mounting the camera onto a wall or other upright surface, position the cables 

straight down to prevent rain infiltration.

•  If wiring the camera through the wiring hole on the bottom, use silicone sealant or a 

rubber mat to ensure waterproofing. Also use an insect repellent sponge if necessary.

•  When wiring by connecting the camera to the composite pipe (3/4 inch NPSM 

threaded hole), wrap the sealing tape around where the pipe connects as necessary 

to prevent rainwater or other moisture from seeping in, clear away any debris and then 

tighten it firmly. Also, apply silicon sealant or a similar substance as necessary to seal 

the pipe tightly after attachment.

•  Firmly fix the dome case to the main unit of the camera with the lock screws, taking 

care not to pinch cables between the main unit and dome case.

 

Failure to follow the instructions may result in death or serious injury.

•  If you discover defective conditions such as smoke, strange sounds, heat or strange odors, 

immediately stop using the camera and contact your nearest dealer.

Fire or electric shock may result from continued use of the product.

•  If thunder starts, stop installation or inspection etc. and do not touch the camera or continue 

connecting the cable.

•  Do not disassemble or modify the camera.

•  Do not damage the connecting cable.

•  Do not insert foreign objects such as water or metal into the camera.

•  Do not use flammable sprays near the camera.

•  Do not leave LAN cables, external power supply, or the power connector for the AC adapter (

sold 

separately

) connected when the camera is not in use for long periods.

•  Do not use flammable solvents such as alcohol, paint thinner or benzine when cleaning the camera.

Failure to do so may result in fire or electric shock.

Please refer to the installation procedures or the Appendix – Specifications for specifications not listed below.

Camera

Lens 

2.4x optical zoom (4x digital zoom) lens (electric drive)

Viewing Angle 

For 16:9 aspect ratios

   

   Horizontal: 122.1° (W) – 50.1° (T)

   

   Vertical: 65.9° (W) – 28.1° (T)

   

For 4:3 aspect ratios

   

   Horizontal: 89.2° (W) – 37.5° (T)

   

   Vertical: 65.9° (W) – 28.1° (T)

Min. Subject Illumination  Day Mode (color):
   

   0.035 lux (F1.2, shutter speed 1/30 sec., when smart shade control is off, 50IRE)

   

Night Mode (monochrome):

   

   0 lux (F1.2, shutter speed 1/30 sec., when smart shade control is off, 50IRE with IR light on)

   

   0.002 lux (F1.2, shutter speed 1/30 sec., when smart shade control is off, 50IRE)

   

When using the Dome Unit (Smoked) (sold separately)

   

Day Mode (color):

   

   0.07 lux (F1.2, shutter speed 1/30 sec., when smart shade control is off, 50IRE)

   

Night Mode (monochrome):

   

   0.004 lux (F1.2, shutter speed 1/30 sec., when smart shade control is off, 50IRE)

IR Illumination Range  20 m (65.6 ft.)
Pan Angle Range 

360° (±180°)

Tilt Angle Range 

90° (-15° – +75°) 

   

– Camera is at 0° when attached to the ceiling and facing straight down

Rotation Angle Range  350° (+220°/-130°)   +: Clockwise

Interface

Network Terminal 

LAN x 1 (RJ45, 100Base-TX (auto/full-duplex/half-duplex))

Audio Input Terminal 

3.5 mm ( 0.14 in.) mini-jack connector (monaural)

(Common for LINE IN & MIC IN)  LINE IN (connect to an amplifier microphone) or 
   

MIC IN (connect to a microphone w/o amplifier)

   

– Switch LINE IN/MIC IN in the Setting Page.

Audio Output Terminal   3.5 mm ( 0.14 in.) mini-jack connector (monaural)
(LINE OUT) 

LINE OUT (connect to an amplifier speaker)

External Device I/O Terminal  Input x 2, Output x 2
   

Analog Video Output x 1

Memory Card * 

microSD Memory Card, microSDHC Memory Card, microSDXC Memory Card Compatible. 
*  To insure reliability in the recording speed, it is recommended to use CLASS 10 rated products. Even when 

using CLASS 10 products, reliability cannot be guaranteed during heavy access loads (e.g., when recording 
and deleting data at the same time).

Others

Operating Environment  Temperature: 
   

When the heater unit (sold separately) is installed

   

   Operating Temperature Range:

   

      AC, PoE+: -40°C – +55°C (-40°F – +131°F)

   

   Start-up Temperature Range:

   

      AC, PoE+: -30°C – +55°C (-22°F – +131°F)

   

– Sunshade cover (sold separately) necessary when under direct sun exposure

   

When the heater unit (sold separately) is not installed

   

   AC, DC, PoE+, PoE: -10°C – +55°C (+14°F – +131°F)

   

– Sunshade cover (sold separately) necessary when under direct sun exposure

   

Humidity

   

   5% – 85% (without condensation)

Storage Environment 

Temperature: -30°C – +60°C (-22°F – +140°F)  
Humidity: 5% – 90% (without condensation)

Installation Method 

Ceiling mount/Surface mount

Power Supply 

PoE: PoE power supply via LAN connector (IEEE802.3at Type1/Type2 compliant)

   

AC Adapter: PA-V18 (100 – 240 V AC) (sold separately)

   

External power source: 24 V AC/12 V DC

Power Consumption 

PoE+: Max. approx. 12.4 W*

1

   

 

Max. approx. 23.1 W*

1

 *

2

   

PoE: Max. approx. 12.4 W*

3

   

AC Adapter PA-V18: Max. approx. 15.2 W (100 V AC)

   

 

Max. approx. 15.2 W (240 V AC)

   

DC: Max. approx. 13.8 W

   

AC: Max. approx. 12.7 W

   

 

Max. approx. 24.1 W*

2

   

*

1

 Class 4 power sourcing equipment (requests 30.0 W)

   

*

2

 When the heater unit (sold separately) is installed

   

*

3

 Class 0 power sourcing equipment (requests 15.4 W)

Weight 

Approx. 1850 g (4.08 lb.) 

Impact Resistance 

IK10 (20J)

Dust-resistant/
Waterproof Specification  IP66

9

6

8

11

4

5

3

2

1

12

13

7

14 15

10

16

17

Serial_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 

MAC_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

1. Dome case lock screw / 2. Dome case / 3. Reboot switch / 4. Installation adjustment switch / 
5. Power connection terminal / 6. Analog video output terminal / 7. Audio I/O terminal / 8. Lens unit / 
9. 100Base-TX LAN connector / 10. Heater connection terminal / 11. LED (Blue)* / 
12. External device I/O terminals / 13. Fan / 14. Visible light sensor / 15. Memory card slot / 
16. Infrared illumination / 17. Connection slot 
* On: when powered on, during reboot / Off: during normal use

Camera mounting tab slots

145 (5.71)

180

(7.09)

R62 (R2.44)

Unit: mm (in.)

Unit: mm (in.)

10-  4.5 (  0.18) 

(*1*2)

6.6 (0.26)

18.5 (0.73)

83.5 (3-9/32) 

(*4)

85.7 (3-3/8) 

(*3*4)

85.7 (3-3/8) 

(*

3*

4)

46

 (

1-

13

/1

6)

 

(*

3*

4)

85.7 (3-3/8)

 

(*

4)

4.5 (0.18)

4.5 (0.18)

4.5 (0.18)

171 (6.73)

*1 Ceiling/Wall mount holes

*2 Junction box fixing holes

*3 Ceiling/Wall mount holes position

*4 Junction box fixing holes position

Set the IP address and other network information on the camera using the “Camera Management Tool” on the 

Setup CD-ROM.

For details on how to operate the “Camera Management Tool”, please refer to the  “Camera Management Tool 

User Manual”.

The analog video output video image is used by this camera to adjust the camera’s viewing angle.

Remove the outer tape. When installing on a ceiling, use a coin to remove the connection slot cover and then 

attach it to the connection slot on the outside. Remove the dome case and remove the tape and polystyrene foam 

attached to the lens for shipping purposes.

When guiding cables through 

the side

When guiding cables through 

the ceiling wiring hole

❶

❷

Dedicated wrench

Remove the dome case and place the memory card in the memory card 

slot.

To remove the memory card, push it in all the way until the card slightly 

pops out and remove.

 Important

•  Insert a memory card before installing the camera.
•  When using a memory card with the camera for the first time, it is 

recommended to format the card after inserting it into the camera (please refer 
to “Operation Guide”).

•  Always unmount the memory card before removing it (please refer to 

“Operation Guide”).

Memory card slot

Connect the two heater cables included with the heater unit to the terminals on the camera side. Next, attach the 

heater unit to the camera body and then tighten the screws. Finally, connect the cables to the heater unit.

❶

❷

❸

Remove the dome case from the camera, then remove the dome cover holder and dome flange, and replace with 

the smoked dome.

 Important

•  Take care when replacing so as not to scratch the dome cover.
•  For proper protection against water and dust, please make sure the screws are firmly tightened during installation.

Dome flange

Dome cover

Rubber seal

Dome cover holder

Smoked dome cover

The sunshade cover is attached to the camera body together with the dome case. In order to install it, of the four 

lock screws for the dome case, remove the two located at the top of the dome case beforehand. Remove the 

dome case lock screws by pressing the screws from the inside of the case and using the dedicated wrench to 

loosen them.

Dedicated 

wrench

The following accessories can be purchased separately as necessary. Some accessories are not available in 

certain countries or regions.

Dedicated accessory used to install the camera to the end of pipe that extends from high ceilings, such as in big-box 

stores.

Smoked dome cover.

Dedicated accessory to protect the camera body from direct sunlight.

Dedicated accessory attached to the interior to maintain operation temperature within the dome and achieve stable 

operation even in extremely cold environments.

Dedicated AC adapter for this camera.

The contents of this guide are subject to change without any prior notice.