Craftsman 54931 Manuel D’Utilisation
Features
Your garage door opener is equipped with features to provide you
with greater control over your garage door operation.
with greater control over your garage door operation.
TIMER-TO-CLOSE (DO NOT enable on one-piece doors)
The Timer-to-Close feature automatically closes the door after a
specified time period that can be adjusted using the door control.
Prior to the door closing there will be an audible and visual alert.
The Timer-to-Close feature automatically closes the door after a
specified time period that can be adjusted using the door control.
Prior to the door closing there will be an audible and visual alert.
SMART CONTROL
Smart Control technology uses a 900MHz signal to provide two-
way communication between the garage door opener and Smart
Control accessories. Your garage door opener is compatible with
up to 8 Smart Control accessories.
Smart Control technology uses a 900MHz signal to provide two-
way communication between the garage door opener and Smart
Control accessories. Your garage door opener is compatible with
up to 8 Smart Control accessories.
REMOTE CONTROLS AND DOOR CONTROLS
Your garage door opener has already been programmed at the
factory to operate with your remote control, which changes with
each use, randomly accessing over 100 billion new codes. Older
Craftsman accessories are not compatible.
Your garage door opener has already been programmed at the
factory to operate with your remote control, which changes with
each use, randomly accessing over 100 billion new codes. Older
Craftsman accessories are not compatible.
Accessories
MEMORY CAPACITY
Remote Controls
Up to 8
Door Controls
Up to 2 Smart Garage Door Opener door
controls.
controls.
Keyless Entries
Up to 1
THE PROTECTOR SYSTEM
®
(SAFETY REVERSING SENSORS)
When properly connected and aligned, the safety reversing
sensors will detect an obstruction in the path of the infrared
beam. If an obstruction breaks the infrared beam while the door is
closing, the door will stop and reverse to full open position, and
the opener lights will flash 10 times. If the door is fully open, and
the safety reversing sensors are not installed, or are misaligned,
the door will not close from a remote control. However, you can
close the door if you hold the button on the door control or
keyless entry until the door is fully closed. The safety reversing
sensors do not effect the opening cycle.
sensors will detect an obstruction in the path of the infrared
beam. If an obstruction breaks the infrared beam while the door is
closing, the door will stop and reverse to full open position, and
the opener lights will flash 10 times. If the door is fully open, and
the safety reversing sensors are not installed, or are misaligned,
the door will not close from a remote control. However, you can
close the door if you hold the button on the door control or
keyless entry until the door is fully closed. The safety reversing
sensors do not effect the opening cycle.
ENERGY CONSERVATION
For energy efficiency the garage door opener will enter sleep
mode when the door is fully closed. The sleep mode shuts the
garage door opener down until activated. The sleep mode is
sequenced with the garage door opener light bulb; as the light
bulb turns off the sensor LEDs will turn off and whenever the
garage door opener lights turn on the sensor LEDs will light. The
garage door opener will not go into the sleep mode until the
garage door opener has completed 5 cycles upon power up.
For energy efficiency the garage door opener will enter sleep
mode when the door is fully closed. The sleep mode shuts the
garage door opener down until activated. The sleep mode is
sequenced with the garage door opener light bulb; as the light
bulb turns off the sensor LEDs will turn off and whenever the
garage door opener lights turn on the sensor LEDs will light. The
garage door opener will not go into the sleep mode until the
garage door opener has completed 5 cycles upon power up.
LIGHTS
The garage door opener light bulbs will turn on when the opener
is initially plugged in; power is restored after interruption, or when
the garage door opener is activated. The lights will turn off
automatically after 4-1/2 minutes. An incandescent A19 light bulb
(100 watt maximum) or for maximum energy efficiency a 26W
(100W equivalent) compact fluorescent light (CFL) bulb may be
used.
The garage door opener light bulbs will turn on when the opener
is initially plugged in; power is restored after interruption, or when
the garage door opener is activated. The lights will turn off
automatically after 4-1/2 minutes. An incandescent A19 light bulb
(100 watt maximum) or for maximum energy efficiency a 26W
(100W equivalent) compact fluorescent light (CFL) bulb may be
used.
USING YOUR GARAGE DOOR OPENER
The garage door opener can be activated through a wall-mounted
door control, remote control, wireless keyless entry or Smart
Control accessory.
When the door is closed and the garage door opener is activated
the door will open. If the door senses an obstruction or is
interrupted while opening the door will stop. When the door is in
any position other than closed and the garage door opener is
activated the door will close. If the garage door opener senses an
obstruction while closing, the door will reverse. If the obstruction
interrupts the sensor beam the garage door opener lights will
blink 10 times. However, you can close the door if you hold the
button on the door control or keyless entry until the door is fully
closed. The safety reversing sensors do no effect the opening
cycle.
The safety reversing sensor must be connected and aligned
correctly before the garage door opener will move in the down
direction.
The garage door opener can be activated through a wall-mounted
door control, remote control, wireless keyless entry or Smart
Control accessory.
When the door is closed and the garage door opener is activated
the door will open. If the door senses an obstruction or is
interrupted while opening the door will stop. When the door is in
any position other than closed and the garage door opener is
activated the door will close. If the garage door opener senses an
obstruction while closing, the door will reverse. If the obstruction
interrupts the sensor beam the garage door opener lights will
blink 10 times. However, you can close the door if you hold the
button on the door control or keyless entry until the door is fully
closed. The safety reversing sensors do no effect the opening
cycle.
The safety reversing sensor must be connected and aligned
correctly before the garage door opener will move in the down
direction.
36