Kraft KF-SL 60802 MWB Manuel D’Utilisation

P.06

P.07

    

-  Please remember to disconnect water and power 

   supply immediately after the clothes are washed.  

-  Do not climb up and sit on top cover of the machine.

-  Do not lean against machine door.

-  Please do not close the door with excessive forces.If  

   it is found difficult to close the door,please check if the  

   excessive clothes are put in or distributed well.

-  The household washing machine isn't intended to be 

   built-in.

-  Cautions during Handling Machine

   1.Transport bolts shall be reinstalled to the machine  

       by a specialized person.

   2.The accumulated water shall be drained out of the 

       machine.

   3. Handle the machine carefully. Never hold each prot

       -ruded part on the machine while lifting.Machine door 

       can not be used as the handle during the conveyance.

 -  Notes on disposal:

           This marking indicates that this product should not 

           be disposed with other household wastes throug-

           hout the EU. To prevent possible harm to the 

           environment or human health from uncontrolled  

         waste disposal,recycle it responsibly to promote  

           the sustainable reuse of material resources.To  

           return your used device,please use the collection   

           systems or contact the retailer where the product 

           was purchased. They return and can take this   

           product for environmental safe recycling.

  Inlet pipe 

H (optional)

Inlet pipe 

      C

Transport  

plug

hole 

          Outlet hose 

     support(optional)

Service Panel

Door

Control Panel

Detergent Drawer

Power Plug

Outlet Hose

Detergent Box

P.06

P.07

    

-  Please remember to disconnect water and power 

   supply immediately after the clothes are washed.  

-  Do not climb up and sit on top cover of the machine.

-  Do not lean against machine door.

-  Please do not close the door with excessive forces.If  

   it is found difficult to close the door,please check if the  

   excessive clothes are put in or distributed well.

-  The household washing machine isn't intended to be 

   built-in.

-  Cautions during Handling Machine

   1.Transport bolts shall be reinstalled to the machine  

       by a specialized person.

   2.The accumulated water shall be drained out of the 

       machine.

   3. Handle the machine carefully. Never hold each prot

       -ruded part on the machine while lifting.Machine door 

       can not be used as the handle during the conveyance.

 -  Notes on disposal:

           This marking indicates that this product should not 

           be disposed with other household wastes throug-

           hout the EU. To prevent possible harm to the 

           environment or human health from uncontrolled  

         waste disposal,recycle it responsibly to promote  

           the sustainable reuse of material resources.To  

           return your used device,please use the collection   

           systems or contact the retailer where the product 

           was purchased. They return and can take this   

           product for environmental safe recycling.

  Inlet pipe 

H (optional)

Inlet pipe 

      C

Transport  

plug

hole 

          Outlet hose 

     support(optional)

Service Panel

Door

Control Panel

Detergent Drawer

Power Plug

Outlet Hose

Detergent Box

P.06

P.07

    

-  Please remember to disconnect water and power 

   supply immediately after the clothes are washed.  

-  Do not climb up and sit on top cover of the machine.

-  Do not lean against machine door.

-  Please do not close the door with excessive forces.If  

   it is found difficult to close the door,please check if the  

   excessive clothes are put in or distributed well.

-  The household washing machine isn't intended to be 

   built-in.

-  Cautions during Handling Machine

   1.Transport bolts shall be reinstalled to the machine  

       by a specialized person.

   2.The accumulated water shall be drained out of the 

       machine.

   3. Handle the machine carefully. Never hold each prot

       -ruded part on the machine while lifting.Machine door 

       can not be used as the handle during the conveyance.

 -  Notes on disposal:

           This marking indicates that this product should not 

           be disposed with other household wastes throug-

           hout the EU. To prevent possible harm to the 

           environment or human health from uncontrolled  

         waste disposal,recycle it responsibly to promote  

           the sustainable reuse of material resources.To  

           return your used device,please use the collection   

           systems or contact the retailer where the product 

           was purchased. They return and can take this   

           product for environmental safe recycling.

  Inlet pipe 

H (optional)

Inlet pipe 

      C

Transport  

plug

hole 

          Outlet hose 

     support(optional)

Service Panel

Door

Control Panel

Detergent Drawer

Power Plug

Outlet Hose

Detergent Box

P.08

P.09

3.Ensure the positioning status of washing machine. Loosen the lock nut with spanner

   and turn the leg with hand until it closely contacts with the floor. Press the leg with one 

   hand and fasten the nut closely to the cabinet with the other hand.

4.After being locked properly, press four corners again to make sure that they has been 

   adjusted properly. If it is still unstable, it has to repeat Steps 2 and 3.

 

    

   

      Connect inlet pipe

Connect the inlet pipe as indicated in the figure.

For the model which has hot valve , please connect 

the hot vale to hot water tap. Energy will decrease 

automatically for some program.

   

      Install inlet pipe

1.Connect the elbow to tap and fasten it 

   clockwise.

2.Connect the other end of inlet pipe to the inlet 

   valve at the backside of washing machine and 

   fasten the pipe tightly clockwise.

Notes: after connection, if there is any leakage 

with hose, then repeat the steps to connect inlet

pipe. The most common type of tap shall be 

used to supply water. If tap is square or too big, 

then standard tap shall be changed.

      Place outlet hose

There are two ways to place the end of outlet hose:

1.Put it beside the water trough.

 

   

Unpack your washing machine and check if there is any damage during the transportation. 

Also make sure that all the items (as shown in Page 5) in the attached bag are received. 

If there is any damage to the washing machine during the transportation, or any item is 

missing, please contact the local dealer immediately.
    

The packing materials of this machine may be dangerous to kids. Please dispose them 

properly and avoid easy touch by kids. Please dispose the related packing materials 

according to the relevant local regulations. Please do no throw the packing materials 

away together with the other daily living rubbishes. 
    

Before using this washing machine, transport bolts 

must be removed from the backside of

this machine. Please take the following steps to 

remove the bolts:

1.Loosen all bolts with spanner and then remove them.

2.Stop the holes with transport hole plugs.

3.Keep the transport bolts properly for future use.
    

Before installing the washing machine, the location characterized as follows shall be

selected:

-   Rigid, dry, and level surface (if not level, please make it level with reference to the

    following figure “Adjust Leg”)

-   Avoid direct sunlight

-   Sufficient ventilation

-   Room temperature is above 0 C 

-   Keep far away from the heat resources such as coal or gas.

Make sure that the washing machine will not stand on power cord.

Do not install the washing machine on the carpet floor.
     

1.When positioning the washing machine, please 

   first check if the legs are closely attached to the 

   cabinet. If not, please turn them to their original 

   positions with hand or spanner and tighten the 

   nuts with spanner.

2.After positioning the washing machine, press 

   four corners on top cover of washing machine 

   in sequence. If the washing machine is not 

   stable when being pressed, this leg shall be 

   adjusted.

5.Put a solid cylinder (e.g. pop cans) oppositely on the top cover of the washing machine from in 
the left, right, front and back directions. If the cylinder keeps stable, the washing machine is
 positioned level. If it rolls, the washing machineis positioned unlevel. The rolling direction is the 
direction of lower ground surface.Then, the two legs in this direction shall be raised at the same time
 until the washing machine is level. Steps 1~3 are repeated to make the bottom legs closely against 
the ground and the nuts shall be locked tightly.