Zelmer ZCK 1171 X/17 Z 012 inox Manuel D’Utilisation
35
GW17-046_v02
Technical data
The technical parameters are given on the data plate of the
product.
1.7 liter capacity.
Zelmer electric kettles are built in I class insulation and they
are equipped with supplying cord with grounding wire and
grounding plug.
The ZELMER kettle meets the requirements of the standards
in force.
The appliance is compliant with the requirements of the
following directives:
The Low Voltage Directive (LVD) – 2006/95/EC.
–
Electromagnetic Compatibility (EMC) – 2004/108/EC.
–
The product is affixed with a CE Mark on the data plate.
The product is affixed with a CE Mark on the data plate.
Structure of the kettle
(Fig. A)
1
Control light
2
Metal casing
3
Spout
4
Lid release button
5
Lid
6
Handle cover
7
Handle
8
Water level indicator
9
On/off button
10
Base of the kettle
11
Supplying cord
12
Storage space for the connecting cord
13
Antideposit filter
14
Base
Preparation of the electric kettle for
operation
Before the first use, wash the kettle inside
(for washing instructions see “Cleaning and
maintenance”), fill it with water up to the “max”
level, and let it boil four times (use fresh water
each time) and wash again.
Operating instructions of the electric kettle
(Fig. B)
1
Press the lid button (4) – the kettle lid will open.
2
Place the filter (13) in the kettle – if it was taken out before.
3
Fill the kettle up with the desired amount of water (the
level is visible on the indicator (8)).
Do not boil the water if it is below the minimum
level or beyond the maximum level on the
indicator (8).
4
Close the lid.
5
Place the kettle on the power base (14).
6
Put the plug of the connecting cord into a mains socket
with an earth pin – the upper part of the kettle body will
light up.
7
Turn the kettle on by pressing the lever (9) – the indicator
light will come on.
8
The kettle switches off automatically when the water
has reached the boiling point, the lever switch returns to its
starting position – the light comes off.
If further use of the kettle is anticipated, it is not necessary
If further use of the kettle is anticipated, it is not necessary
to remove the plug of the connecting cord from the power
socket.
Be careful not to fill up with water beyond the
nominal capacity when pouring water into the
kettle.
The rising of the water level in the kettle is delayed in relation
to the speed of pouring the water. It is caused by the filter
slowing down the speed of the flow. This can be prevented by
pouring the last portions of water extremely carefully before
the water reaches the maximum level on the indicator.
In the event that an empty kettle is switched on, it will be
switched off by a thermal device automatically.
In order to switch the kettle on again after it has cooled down
(approx. 15 minutes), take it off the base, replace it and
switch the kettle on by pressing the lever (9). The cooling
down of the kettle can be accelerated by puring cold water
into the kettle.
Cleaning and maintenance
(Fig. C)
Always clean a cold kettle!
1
Remove the plug of the connecting cord from the power
socket.
2
Take out the filter (13).
3
Clean the outside surfaces with a soft cloth moistened
with washingup liquid.
In order to remove the buildup of hard water film from the
In order to remove the buildup of hard water film from the
outside and inside walls of the kettle, wipe them with a cloth
moistened with vineger.
4
Rinse the kettle with fresh water.
Filter replacement – descaling
In the event that scale builds up on the bottom of the kettle,
it needs to be removed. 6% or 10% vinegar is used for this
purpose.
Open the lid
●
(4).
Take out the filter
●
(14).
Wash the filter under running water.
●
Pour in 0.5 l of vinegar and switch on the kettle
●
(9).
Boil the vinegar and leave in the kettle for about 30
●
minutes.