Fujifilm Uvijet KN Fascicule
Uvijet KN
UV Curing Ink System for Acuity Select Inkjet Printers
PRODUCT INFORMATION
Features
• High performance conventional UV ink system
• Good adhesion to rigid plastic substrates
• High satin finish
• Excellent colour gamut
• Excellent inter-coat lay for back lit and solid prints
• Recommended for indoor and external applications
• Good adhesion to rigid plastic substrates
• High satin finish
• Excellent colour gamut
• Excellent inter-coat lay for back lit and solid prints
• Recommended for indoor and external applications
Ink Properties
The Uvijet KN ink range is a high quality UV curable
inkjet system designed for piezo drop-on-demand
printheads. The ink has been specially developed for
the Acuity Select printers and offers excellent dot
reproduction, light-fast colours and will adhere to a
range of rigid and flexible uncoated materials.
inkjet system designed for piezo drop-on-demand
printheads. The ink has been specially developed for
the Acuity Select printers and offers excellent dot
reproduction, light-fast colours and will adhere to a
range of rigid and flexible uncoated materials.
Colour Range
KN052 Yellow
KN867 Magenta
KN335 Light Magenta
KN215 Cyan
KN255 Light Cyan
KN867 Magenta
KN335 Light Magenta
KN215 Cyan
KN255 Light Cyan
KN004 Black
Supplied in 2 litre sealed pouches
KN021 White
KN391 Clear
KN021 White
KN391 Clear
Supplied in 1 litre sealed pouches
QV017 UV Flush
QV017 UV Flush
Available in 1 litre containers.
Application Range
Uvijet KN inks are specifically formulated to maximise
the performance of the Fujifilm Acuity Select printers.
the performance of the Fujifilm Acuity Select printers.
Performance of ink on substrate may vary across
substrate manufacturers.
substrate manufacturers.
THE END USER MUST DETERMINE THE
SUITABILITY OF THIS PRODUCT FOR THE
INTENDED USE PRIOR TO PRODUCTION.
SUITABILITY OF THIS PRODUCT FOR THE
INTENDED USE PRIOR TO PRODUCTION.
Media Type
Adhesion Characteristics
Polycarbonate
Styrene
Acrylic
APET
Priplak
Correx
Dibond
PVC Foam Board
Display Board
Semi Rigid PVC
Self-adhesive PVC
PVC Banner
Excellent Good Fair Poor
Curing
Excellent cure and adhesion are achieved immediately
upon print and UV curing. However, maximum
adhesion, chemical, scuff and scratch resistance may
not be obtained until 24 hours after initial curing.The
actual level of cure will depend upon ink thickness,
substrate and the UV curing lamps being used.
Superior through cure may be obtained by reducing the
print speed by selection of an alternative print mode to
increase the overall UV dose.
upon print and UV curing. However, maximum
adhesion, chemical, scuff and scratch resistance may
not be obtained until 24 hours after initial curing.The
actual level of cure will depend upon ink thickness,
substrate and the UV curing lamps being used.
Superior through cure may be obtained by reducing the
print speed by selection of an alternative print mode to
increase the overall UV dose.
Pre-production Tests
Uvijet KN ink is formulated to give good adhesion to
most major brands of plastic and polyethylene
materials. Polyolefins should have a surface energy
level of 42 dynes/cm or higher. However it is strongly
recommended that all substrates are tested before a
commercial run. For information on adhesion promoters
refer to the Uvijet Fusion Primer range.
most major brands of plastic and polyethylene
materials. Polyolefins should have a surface energy
level of 42 dynes/cm or higher. However it is strongly
recommended that all substrates are tested before a
commercial run. For information on adhesion promoters
refer to the Uvijet Fusion Primer range.