Cisco Cisco IOS Software Release 12.0(21)S1
1-Port Channelized OC-48/STM-16 ISE and 4-Port Channelized OC-12/STM-4 ISE Line Cards for the Cisco 12000 Series
Using show Commands to Verify Controller and Interface Status
43
1-Port Channelized OC-48/STM-16 ISE and 4-Port Channelized OC-12/STM-4 ISE Line Cards for the Cisco 12000 Series Router
Cisco IOS Release 12.0(33)S4
Terminating a BER Test
You can terminate a BER test with the no bert configuration command as follows:
router# configure terminal
router(config)# interface serial5/0:2
router(config-if)# no bert
router(config-if)# end
Using show Commands to Verify Controller and Interface Status
After installing the line card, use show commands to display the status of the controller and the
interfaces. Following are descriptions and examples of the show commands you can use to check the
configuration. In the following examples, descriptions are limited to fields that are relevant for verifying
the configuration of the 1-Port Channelized OC-48/STM-16 ISE and 4-Port Channelized OC-12/STM-4
ISE line cards.
interfaces. Following are descriptions and examples of the show commands you can use to check the
configuration. In the following examples, descriptions are limited to fields that are relevant for verifying
the configuration of the 1-Port Channelized OC-48/STM-16 ISE and 4-Port Channelized OC-12/STM-4
ISE line cards.
Using the show version Command
Use the show version command to display the configuration of the system hardware (the channel of each
line card installed), the software release, the names and sources of configuration files, and the boot
images. Ensure that the list includes the new 1-port channelized OC-48/STM-16 ISE and 4-port
channelized OC-12/STM-4 ISE line card interface.
line card installed), the software release, the names and sources of configuration files, and the boot
images. Ensure that the list includes the new 1-port channelized OC-48/STM-16 ISE and 4-port
channelized OC-12/STM-4 ISE line card interface.
router# show version
Cisco Internetwork Operating System Software
IOS (tm) GS Software (GSR-P-M), Experimental Version 12.0(20010922:053231) [jingwan-rel2
113]
Copyright (c) 1986-2001 by cisco Systems, Inc.
Compiled Tue 25-Sep-01 22:01 by jingwan
Image text-base:0x50010968, data-base:0x523E6000
ROM:System Bootstrap, Version 11.2(17)GS2, [htseng 180] EARLY DEPLOYMENT RELEASE SOFTWARE
(fc1)
BOOTLDR:GS Software (GSR-BOOT-M), Version 12.0(8)S, EARLY DEPLOYMENT RELEASE SOFTWARE
(fc1)
TOP1.2.6C uptime is 13 hours, 48 minutes
System returned to ROM by reload at 20:44:53 UTC Tue Sep 25 2001
System image file is "tftp://10.1.1.253/gsr-p-mz:120-20.3.S"
cisco 12008/GRP (R5000) processor (revision 0x01) with 262144K bytes of memory.
R5000 CPU at 200Mhz, Implementation 35, Rev 2.1, 512KB L2 Cache
Last reset from power-on
1 Route Processor Card
2 Clock Scheduler Cards
3 Switch Fabric Cards
1 OC48 channelized to STS-48c/STM-16, STS-12c/STM-4,
STS-3c/STM-1 or DS-3/E3 controller
1 Ethernet/IEEE 802.3 interface(s)
1 Packet over SONET network interface(s)
4 SDCC network interface(s)
507K bytes of non-volatile configuration memory.
20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K).
8192K bytes of Flash internal SIMM (Sector size 256K).
Configuration register is 0x0
router#