Intel 7140M LF80550KG096007 Fiche De Données
Codes de produits
LF80550KG096007
Intel® Xeon® Processor 7400 Series Datasheet
37
Electrical Specifications
2.13
Front Side Bus AC Specifications
The processor FSB timings specified in this section are defined at the
processor core (pads). Therefore, proper simulation of the FSB is the only
means to verify proper timing and signal quality.
processor core (pads). Therefore, proper simulation of the FSB is the only
means to verify proper timing and signal quality.
for signal definitions.
through
list the AC specifications associated with the processor FSB.
All AGTL+ timings are referenced to GTLREF_DATA_MID, GTLREF_DATA_END,
GTLREF_ADD_MID, and GTLREF_ADD_END for both ‘0’ and ‘1’ logic levels unless
otherwise specified.
GTLREF_ADD_MID, and GTLREF_ADD_END for both ‘0’ and ‘1’ logic levels unless
otherwise specified.
The timings specified in this section should be used in conjunction with the processor
signal integrity models provided by Intel. AGTL+ layout guidelines are also available in
the appropriate platform design guidelines.
signal integrity models provided by Intel. AGTL+ layout guidelines are also available in
the appropriate platform design guidelines.
Note:
Care should be taken to read all notes associated with a particular timing parameter.
Notes:
1.
Unless otherwise noted, all specifications in this table apply to all processor frequencies.
2.
The processor core clock frequency is derived from BCLK. The bus clock to processor core clock ratio is
determined during initialization as described in
includes core frequency to FSB
multipliers.
3.
The period specified here is the average period. A given period may vary from this specification as
governed by the period stability specification (T2).
4.
For the clock jitter specification, refer to the CK410B Clock Synthesize/Driver Design Guidelines.
5.
In this context, period stability is defined as the worst case timing difference between successive crossover
voltages. In other words, the largest absolute difference between adjacent clock periods must be less than
the period stability.
6.
Rise and fall times are measured single ended between 245 mV and 455 mV of the clock swing.
7.
Measured from -200 mV to +200 mV. The signal must be monotonic through the measurement region for
rise and fall time. The 400 mV measurement window is centered on the differential zero. See
.
Notes:
1.
Unless otherwise noted, all specifications in this table apply to all processor frequencies.
2.
Not 100% tested. Specified by design characterization.
3.
All common clock AC timings for AGTL+ signals are referenced to the Crossing Voltage (V
CROSS
) of the
BCLK[1:0] at rising edge of BCLK0. All common clock AGTL+ signal timings are referenced at nominal
GTLREF_DATA_MID, GTLREF_DATA_END, GTLREF_ADD_MID, and GTLREF_ADD_END at the processor
(pads).
Table 2-19. Front Side Bus Differential Clock AC Specifications
T# Parameter
Min
Typ
Max
Unit
Figure
Notes
1
FSB Clock Frequency
265.247
266.666
266.745
MHz
2
T1: BCLK[1:0] Period
3.7489
3.7500
3.7700
ns
3
T2: BCLK[1:0] Period Stability
150
ps
4, 5
T3: BCLK[1:0] Rise Time
700
ps
6
T4: BCLK[1:0] Fall Time
700
ps
6
Differential Rising and Falling Edge
Rates
0.6
4
V/ns
7
Table 2-20. Front Side Bus Common Clock AC Specifications
T# Parameter
Min
Max
Unit
Figure
Notes
1, 2, 3
T10: Common Clock Output Valid Delay
0.22
1.10
ns
4
T11: Common Clock Input Setup Time
0.650
N/A
ns
5
T12: Common Clock Input Hold Time
0.150
N/A
ns
5
T13: RESET# Pulse Width
1
10
ms
6, 7, 8